Sharp AR-407 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Kopierer Sharp AR-407 herunter. Sharp AR-407 User's Manual Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 184
  • Inhaltsverzeichnis
  • FEHLERBEHEBUNG
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 0
GETTING STARTED
MAKING COPIES
SPECIAL FUNCTIONS
SUPPLIES
COPIER TROUBLE?
GENERAL
INFORMATION
OPTIONAL EQUIPMENT
KEY OPERATOR’S
GUIDE
1-1
2-1
3-1
4-1
5-1
6-1
7-1
8-1
DIGITAL COPYING MACHINE
OPERATION MANUAL
Page
AR-407
AR-287/AR-337
MODEL
AR-287
AR-337
AR-407
Seitenansicht 0
1 2 3 4 5 6 ... 183 184

Inhaltsverzeichnis

Seite 1 - AR-287/AR-337

• GETTING STARTED• MAKING COPIES• SPECIAL FUNCTIONS• SUPPLIES• COPIER TROUBLE?• GENERAL INFORMATION• OPTIONAL EQUIPMENT • KEY OPERATOR’S GUIDE1-12-13

Seite 2

1-6CHAPTER1GETTING STARTED Power on and offAuto power shut-off modeIf the auto power shut-off mode is enabled, the copier willautomatically turn off

Seite 3 - CONTENTS

5-12CHAPTER5COPIER TROUBLE? TroubleshootingTROUBLESHOOTINGAlways check the message display whenever the copier stops oroperation is not possible. The

Seite 4

5-13CHAPTER5TROUBLESHOOTINGCOPIER TROUBLE? TroubleshootingProblem SolutionDust, dirt, smudges appearon copies.Touch panel is too dark ortoo light.“CH

Seite 6 - INSTALLATION REQUIREMENTS

6-1CHAPTER6CHAPTER 6GENERAL INFORMATIONThis chapter describes general information for using this copier. Page●●●●

Seite 7 - CAUTIONS

6-2CHAPTER6PART NAMES AND FUNCTIONSExteriorExit area coverOpen to remove misfed paper.Power switchPress to turn copier power on and off.Exit tray (opt

Seite 8

6-3CHAPTER6PART NAMES AND FUNCTIONSInteriorGENERAL INFORMATIONPart names and functionsBypass tray paper guidesAdjust to the width of the copy paper.By

Seite 9

6-4CHAPTER6PART NAMES AND FUNCTIONSOperation PanelLCD touch panelDisplays information to assist the operator.Various operation keys are included in th

Seite 10 - Power save modes

6-5CHAPTER6PART NAMES AND FUNCTIONSCUSTOM SETTINGS ( ) keyPress to set key operator programs or adjust thecontrast of the touch panel.2-SIDED COPY key

Seite 11 - INFORMATION FUNCTION

6-6CHAPTER6USER MAINTENANCEThe document glass and the document cover (RADF transport belt)must be kept clean to avoid dirty areas from being copied on

Seite 12 - USING THE TOUCH PANEL

6-7CHAPTER6TOUCH PANEL CONTRAST ADJUSTMENTThe contrast of the touch panel can be adjusted as below.1Press the CUSTOM SETTINGS ( ) key.2Press the “DISP

Seite 13 - Function setting icons

1-7CHAPTER11Press the INFORMATION ( ) key in the standby mode.●The screen for the information categories will appear.2Select the “COPIER” key to displ

Seite 14

6-8CHAPTER6SPECIFICATIONSGENERAL INFORMATIONSpecificationsCOPIERAR-287 AR-337 AR-407Type DesktopCopy system Dry, electrostatic transfer systemOriginal

Seite 15 - CHAPTER 2

6-9CHAPTER6SPECIFICATIONSGENERAL INFORMATIONSpecificationsDUPLEX MODULEPaper type Ordinary paper onlyNumber of copies 1 (trayless system)Copy paper si

Seite 17 - USING THE RADF

7-1CHAPTER7CHAPTER 7OPTIONAL EQUIPMENTThis chapter describes operating instructions for the Finisher (AR-FN1N,AR-FN2), Large Capacity Tray (AR-LC1N),

Seite 18

7-2CHAPTER7SYSTEM CONFIGURATIONThe options which are available for this copier are shown below.OPTIONAL EQUIPMENTSystem configurationLarge capacity tr

Seite 19

7-3CHAPTER7FINISHER (AR-FN1N)The copier has two different finisher modes: one sorts copies into sets matching the sequence of the originals andthe sec

Seite 20

7-4CHAPTER7Offset stackOFFSET modeWhen copying in the SORT mode, each collated set ofcopies will be stacked offset approximately 30 mm (1.2inch) from

Seite 21

7-5CHAPTER7Sort and groupWhen SORT is selected, the SORT ( ) icon will be indicated andcopies will be collated by sets.When STAPLE SORT is selected, t

Seite 22 - COPY RATIO

7-6CHAPTER7Staple sortThe STAPLE SORT mode staples A4, A4R, B4, and A3 (8-1/2" x 11",8-1/2" x 11"R, 8-1/2" x 14", and 11

Seite 23 - Original size detector

7-7CHAPTER74Select the desired stapling position.●The AR-FN1N finisher has three selectable stapling positions asshown below. 5Press the “OK” key.6S

Seite 24 - CLEAR ALL

1-8CHAPTER1USING THE TOUCH PANELHow to use the touch panelYou can set or cancel a function displayed on the touchpanel by pressing (touching) a key wi

Seite 25 - Automatic selection

7-8CHAPTER7Using the document glass1Set the original on the document glass with the cornerto be stapled to the upper right.●Copy from the last page to

Seite 26 - REDUCTION/ENLARGEMENT/ZOOM

7-9CHAPTER75Press the “OK” key.6Set the number of copies.7Press the START ( ) key.8Replace the finished original with the next original afterthe START

Seite 27

7-10CHAPTER7Staple cartridge replacementThe message “SLIDE THE FINISHER AWAY FROM THE COPIERAND ADD STAPLES.” will appear when the staple cartridge is

Seite 28

7-11CHAPTER76Insert the new staple cartridge into the box until it clicksin place.●Insert the new cartridge by aligning the arrows on the cartridgewit

Seite 29

7-12CHAPTER7Staple jam removalIf staples become jammed in the stapler, “CHECK STAPLER POSITIONOR STAPLE JAM.” will be displayed. Remove the jammed st

Seite 30 - EXPOSURE ADJUSTMENTS

7-13CHAPTER76Return the lever to its original position.7Insert the staple box to the stapler unit until it clicks inplace.8Return the stapler unit to

Seite 31 - SORT/GROUP

7-14CHAPTER7OPTIONAL EQUIPMENTFinisher (AR-FN1N)FINISHER (AR-FN1N)A MISFEED HAS OCCURRED.CLEAR INDICATED AREA.PRESS FOR RECOVERY INSTRUCTIONS.Misfee

Seite 32 - Storing a job program

7-15CHAPTER7OPTIONAL EQUIPMENTFinisher (AR-FN1N)FINISHER (AR-FN1N)3If the misfed paper cannot be removed in step 2, openthe cover of the paper feed ar

Seite 33 - JOB MEMORY

7-16CHAPTER7OPTIONAL EQUIPMENTFinisher (AR-FN1N)FINISHER (AR-FN1N)A MISFEED HAS OCCURRED.CLEAR INDICATED AREA.PRESS FOR RECOVERY INSTRUCTIONS.8Push

Seite 34 - INTERRUPT

7-17CHAPTER7OPTIONAL EQUIPMENTFinisher (AR-FN1N)FINISHER (AR-FN1N)3Open the paper transport area cover of the finisher.4Use the transport area lever t

Seite 35 - CHAPTER 3

1-9CHAPTER1Function setting iconsSelected special functions are indicated with their icons onthe basic screen. The setting screen for a selected funct

Seite 36

7-18CHAPTER7OPTIONAL EQUIPMENTFinisher (AR-FN1N)FINISHER (AR-FN1N)Roller rotating knob7Remove the misfed paper.●Remove the misfed paper from the paper

Seite 37

7-19CHAPTER7FINISHER (AR-FN2)The copier has two different finisher modes: one sorts copies into setsmatching the sequence of the originals and the sec

Seite 38 - MARGIN SHIFT

7-20CHAPTER7In the initial setting, the top tray is selected.To select the offset tray, press the OUTPUT key and then the“OFFSET TRAY” key on the touc

Seite 39

7-21CHAPTER7Sort and groupSORT modeEach set of copies will be sequentially delivered to theoffset tray or the top tray as selected.GROUP modeAll copie

Seite 40 - READY TO CO

7-22CHAPTER7Staple sortThe STAPLE SORT mode staples A4 (8-1/2" x 11") size copies.Stapled sets cannot be delivered to the top tray.NOTE:Diff

Seite 41 - READ-END

7-23CHAPTER74Press the “OK” key.5Set the number of copies.●If A4 (8-1/2" x 11") paper has not been selected, press the“PAPER SELECT” key and

Seite 42 - DUAL PAGE COPYING

7-24CHAPTER7Using the document glass1Set the original on the document glass with the cornerto be stapled to the upper right.●Copy from the last page t

Seite 43 - AUTO IMAGE

7-25CHAPTER75Set the number of copies.●If A4 (8-1/2" x 11") paper is not selected, press the “PAPERSELECT” key and select a paper tray conta

Seite 44 - MULTI SHOT

7-26CHAPTER7Staple cartridge replacementThe message “ADD STAPLES.” will appear when the staplecartridge is empty. Replace the staple cartridge as foll

Seite 45 - Select a type of border line

7-27CHAPTER7Staple jam removal1Close and open the stapler cover.2Remove all copies from the tray.3Insert a new sheet of paper (A4 or 8-1/2” x 11” size

Seite 47

7-28CHAPTER7Misfeed removal1If the offset tray has been used, remove the misfedpaper.2While holding the finisher release lever, slide thefinisher away

Seite 48 - T ON FRONT COVER?

7-29CHAPTER75Remove the misfed paper.6Rotate the paper feed area cover as shown to open it.7Remove the misfed paper.8Open the paper guide and remove t

Seite 49

7-30CHAPTER7SpecificationsPaper size A4 (8-1/2" x 11")Paper weight 56 to 105 g/m2 (15 lbs. to 28 lbs.)Paper capacity 3,000 sheetsWeight Appr

Seite 50 - THE INSERT

7-31CHAPTER7Loading copy paperThe large capacity tray will automatically lower when the tray runs outof paper.1Press the paper tray control button on

Seite 51 - PAMPHLET COPY

7-32CHAPTER7The copier will stop when a misfeed occurs.The message “A MISFEED HAS OCCURRED. CLEAR INDICATEDAREA. PRESS FOR RECOVERY INSTRUCTIONS.” w

Seite 52

7-33CHAPTER73Push the large capacity tray toward the copier and latchit into place.4If misfed paper is not found in step 2, pull the tray out.●When pu

Seite 53 - URE PAPER SELECT COP

7-34CHAPTER7Paper size A4 to A3 (8-1/2" x 11" to 11" x 17")Paper weight 56 to 105 g/m2 (15 lbs. to 28 lbs.)Paper capacity 500 shee

Seite 54 - IMAGE EDITING FUNCTIONS

7-35CHAPTER7Loading copy paperThe method of loading of copy paper for the paper tray of the 500-sheet paper drawer is the same as for the paper trays

Seite 55

7-36CHAPTER7The copier will stop when a misfeed occurs.The message “A MISFEED HAS OCCURRED. CLEAR INDICATEDAREA. PRESS FOR RECOVERY INSTRUCTIONS.” w

Seite 56 - CENTRING

7-37CHAPTER7DUAL TRAY OUTPUT UNIT (AR-TR1)This optional unit can deliver interrupt copies to the lower exit tray.PART NAMESUpper exit tray(AR-TE1)Lowe

Seite 57

2-1CHAPTER2CHAPTER 2MAKING COPIESThis chapter describes the basic copying functions such as normalcopying, reduction/enlargement, and exposure adjustm

Seite 58

7-38CHAPTER7SpecificationsExit tray capacityUpper tray : 250 sheetsLower tray : 100 sheetsPaper size Upper tray : A6 to A3 (5-1/2" x 8-1/2"

Seite 59

8-1CHAPTER8CHAPTER 8KEY OPERATOR’S GUIDEThis chapter contains information on all of the programs used by the keyoperator. The programs allow the key o

Seite 60

8-2CHAPTER8KEY OPERATOR CODE NUMBERRegistering the key operator code number1Press the CUSTOM SETTINGS ( ) key.2Press the “KEY OPERATOR PROGRAMS” key o

Seite 61

8-3CHAPTER86Press the “KEY OPERATOR CODE NUMBER CHANGE.”key.7Choose a new 5-digit code number and enter it using the10-key pad.8Press the OK key.●The

Seite 62

8-4CHAPTER8KEY OPERATOR PROGRAMSA complete list of all key operator programs is provided below. These programs canonly be accessed by first entering t

Seite 63 - BINDING CHANGE

8-5CHAPTER8KEY OPERATOR PROGRAMSCategory Program Name Function Page No.Date Format Sets the initial date format. 8-18SettingDate and Time Adjusts the

Seite 64

8-6CHAPTER8Category Program Name Function Page No.Disabling of Prevents damage to the stapler while awaiting 8-26Stapler repair service.(The stapler

Seite 65

8-7CHAPTER8Using the key operator programs1Press the CUSTOM SETTINGS ( ) key.2Press the “KEY OPERATOR PROGRAMS” key on thetouch panel.●The following d

Seite 66 - TEXT STAMP

8-8CHAPTER85Select the desired category on the touch panel.Example: To select the account control category, press the“ACCOUNT CONTROL” key.6Press the

Seite 67 - 1ST PAGE

8-9CHAPTER8ACCOUNT CONTROLThe programs of this category are used to set the internal auditorfunctions. These programs can be selected by pressing the

Seite 68

2-2CHAPTER2AUDITING ACCOUNTSIf this copier has been programmed in the auditing mode, it will notfunction until an assigned 5-digit account number has

Seite 69

8-10CHAPTER8Resetting AccountThis program is used to reset all audit accounts or to selectively resetindividual accounts.When the “RESETTING ACCOUNT.”

Seite 70

8-11CHAPTER8To register accounts1. Press the “ENTER” key.2. Enter a 5-digit account number (00001 to 99999) usingthe 10-key pad.●Select a number diffe

Seite 71 - POSITION

8-12CHAPTER8To print all registered account numbers1. Press the “PRINT” key.●The copier will start printing. To stop printing after starting,press the

Seite 72

8-13CHAPTER8To set a limit for all accounts1. Press the “LIMIT” (ALL ACCOUNTS) key on the touchpanel.●“ALL” will appear under “ACCOUNT NUMBER”.2. Ente

Seite 73

8-14CHAPTER8OTHER FUNCTION SETTINGSThe programs of this category are used to adjust various settings ofcopier functions. These programs can be selecte

Seite 74

8-15CHAPTER8Add or Change Extra Preset RatiosTwo extra preset copy ratios can be added within both the reductionrange (25% to 99%) and the enlargement

Seite 75

8-16CHAPTER8KEY OPERATOR PROGRAMSInitial Margin Shift SettingSet the initial margin shift value with this program.When the “INITIAL MARGIN SHIFT SETTI

Seite 76

8-17CHAPTER8KEY OPERATOR PROGRAMSInitial Status SettingThe copier will assume the initial settings when it is turned on, when theCLEAR ALL (CA) key is

Seite 77

8-18CHAPTER8Staple Position SettingThis program is used to select the initial stapling position for an optionalfinisher (AR-FN1N only).When the “STAPL

Seite 78 - TANDEM COPY

8-19CHAPTER8Date and Time AdjustmentThis program is used to adjust the date and time which will be used forprinting date.When the “DATE AND TIME ADJUS

Seite 79 - DUAL PAGE

2-3CHAPTER2USING THE RADF●Duplex copying will not work when a non-standardsized paper (or 5-1/2" x 8-1/2" paper) is used.●If the orientation

Seite 80 - SETTING REVIEW

8-20CHAPTER8Size Setting for [EXTRA]The paper sizes in the paper trays (except an optional large capacitytray) can be changed by the users. The copier

Seite 81 - CHAPTER 4

8-21CHAPTER8KEY OPERATOR PROGRAMSTIMER SETTINGSThe programs of this category are used to set the timers for somefunctions. These programs can be selec

Seite 82

8-22CHAPTER8KEY OPERATOR PROGRAMSPreheat Mode SettingPreheat mode functions to control the power consumption by loweringthe temperature of the fusing

Seite 83 - CHAPTER4

8-23CHAPTER8Message Time SettingThis program is used to adjust the length of time that messages aredisplayed in the range of 1 to 12 seconds in 1 seco

Seite 84 - Left guide

8-24CHAPTER8KEY OPERATOR PROGRAMSENABLE/DISABLE SETTINGSThe programs of this category are used to enable or disable somefunctions. These programs can

Seite 85 - ADDING TONER

8-25CHAPTER8KEY OPERATOR PROGRAMSDisabling Deletion of Job ProgramsThis program is used to prevent stored programs from being replacedor deleted. If t

Seite 86

8-26CHAPTER8Disabling of StaplerThis program is used to enable or disable the stapler of the optionalfinisher (AR-FN1N, AR-FN2). If the stapler malfun

Seite 87 - USED TONER DISPOSAL

8-27CHAPTER8Disabling of Second Tray Output in InterruptThis program is used to disable output of copies to the second tray ininterrupt copying for an

Seite 88 - STORAGE OF SUPPLIES

8-28CHAPTER8Disabling of Bypass-Tray When Offset Tray SelectedThis program is used to disable the use of the bypass tray when theoffset tray is select

Seite 89 - CHAPTER 5

8-29CHAPTER8KEY OPERATOR’S GUIDE Key operator assistance callKEY OPERATOR ASSISTANCE CALLWhen the copier is in need of service or care not usually pe

Seite 90 - MISFEED REMOVAL

2-4CHAPTER21-sided copies of 1-sided originals1Adjust the original guides to the size of the originals andset the originals face up in the document fe

Seite 92 - Misfeed in the bypass tray

8-31CHAPTER8KEY OPERATOR CODE NUMBER:FACTORY SETTINGThe following is the factory setting of the Key Operator CodeNumber, which must be used to access

Seite 93

2000C DSC1CINSE1954FC51

Seite 94 - Misfeed in the transport area

Required in IEC-950 (EN 60 950) - Europe • The equipment should be installed near an accessible socket outlet for easy disconnection.Required in Appe

Seite 95

AR-287/AR-337/AR-407SHARP CORPORATIONSHARP ELECTRONICS (U.K.) LTD.Sharp House, Thorp Road, Newton Heath, ManchesterM40 5BEPRINTED IN JAPAN2000C DSC1CI

Seite 96

2-5CHAPTER2MAKING COPIES Using the RADFUSING THE RADF2-sided copies from 1-sided originals1Adjust the original guides to the size of the originals an

Seite 97 - Misfeed in the duplex module

In some areas, the "POWER" switch positions are marked "I" and " " on the copier instead of "ON" and "O

Seite 98

2-6CHAPTER2MAKING COPIES Using the RADFUSING THE RADF2-sided copies from 2-sided originals1Adjust the original guides to the size of the originals an

Seite 99 - MAINTENANCE REQUIRED

2-7CHAPTER21-sided copies from 2-sided originals1Adjust the original guides to the size of the originals andset the originals face up in the document

Seite 100 - TROUBLESHOOTING

2-8CHAPTER2COPYING FROM THE DOCUMENT GLASS1-sided copies of 1-sided originals1Open the document feeder cover and place an originalface down on the doc

Seite 101 - Self-diagnostic function

2-9CHAPTER2MAKING COPIES Copying from the document glassCOPYING FROM THE DOCUMENT GLASS5Press the START ( ) key.●If the copier is in the GROUP mode (

Seite 102

2-10CHAPTER24Press the key on the touch panel.5Press the “OK” key.6Use the 10-key pad to enter the desired number ofcopies.●The number will be shown

Seite 103 - CHAPTER 6

2-11CHAPTER2MAKING COPIES Reduction/Enlargement/ZoomAutomatic selection1Place the original in the document feeder tray or on thedocument glass.●The o

Seite 104 - PART NAMES AND FUNCTIONS

2-12CHAPTER2Manual selection1Place the original in the document feeder tray or on thedocument glass.2Press the “COPY RATIO” key on the touch panel.3Us

Seite 105 - Interior

2-13CHAPTER25Press the “OK” key.6Use the “PAPER SELECT” key to select the paper traywith the desired paper size.●If the AUTO PAPER SELECT mode is on,

Seite 106 - Operation Panel

2-14CHAPTER21Place the original in the document feeder tray or on thedocument glass.2Open the bypass tray.3Set the bypass tray guides to the width of

Seite 107 - Touch Panel (Basic screen)

2-15CHAPTER2Two-sided copying with bypass trayTwo-sided copies can be made manually using the bypass tray,when the heavy paper which is out of spec. f

Seite 108 - USER MAINTENANCE

1CHAPTER 4SUPPLIES●PAPER ... 4-2Types and sizes of copy paper ... 4-2Loading copy paper ... 4-2●ADDING TONE

Seite 109 - CHAPTER6

2-16CHAPTER2AutomaticThis is the standard initial setting for this copier. In this mode, thecharacteristics of an original being copied are “read” by

Seite 110 - SPECIFICATIONS

2-17CHAPTER2MAKING COPIES Sort/group123321321321123332321112SORT/GROUPWhen the SORT ( ) icon is indicated on the touch panel, copieswill be collated

Seite 111

2-18CHAPTER2 JOB MEMORYFrequently used job programs can be stored in one of nine storageregisters. This is convenient for quick job recall without los

Seite 112

2-19CHAPTER2JOB PROGRAMSSTORE/DELETERECALLPRESS PROGRAM NUMBER.EXITMAKING COPIES Job memoryDeleting a stored job program1Follow steps 1 and 2 in “Sto

Seite 113 - CHAPTER 7

2-20CHAPTER21Press the INTERRUPT ( ) key.●When the document feeder is being used, the copier will stopafter completing the copying of the originals wh

Seite 114 - SYSTEM CONFIGURATION

3-1CHAPTER3CHAPTER 3SPECIAL FUNCTIONSThis chapter describes the special copying functions including variousimage editing functions which have been mad

Seite 115 - FINISHER (AR-FN1N)

3-2CHAPTER31Place the original in the document feeder tray or on thedocument glass.2Press the “COPY RATIO” key on the touch panel.3Press the “XY ZOOM”

Seite 116 - NON-OFFSET mode

3-3CHAPTER35Press the Y key.●The copy ratio in the vertical (Y) direction will be highlighted.6Use the reduction, enlargement, and ZOOM ( , )keys to

Seite 117 - STAPLE SORT mode

3-4CHAPTER3SPECIAL FUNCTIONS Margin shiftThe MARGIN SHIFT feature, in its initial setting, automatically shifts the textor image to the right both on

Seite 118 - EXPOSURE

3-5CHAPTER3SPECIAL FUNCTIONS Margin shiftMARGIN SHIFT3Press the “MARGIN SHIFT” key on the touch panel.● The setting screen for MARGIN SHIFT will appe

Seite 119 - (DOCUMENT FEEDER MODE)

2-2CHAPTER2AUDITING ACCOUNTSIf this copier has been programmed in the auditing mode, it will notfunction until an assigned 5-digit account number has

Seite 120

3-6CHAPTER3This copier has an edge erase mode and a centre erase mode.●Edge erase can be used to eliminate shadow lines around the edges ofcopies caus

Seite 121

3-7CHAPTER34Select the desired erase mode.●Select “EDGE ERASE”, “CENTRE ERASE” or “EDGE+CENTREERASE” on the touch panel. The selected erase mode will

Seite 122 - Staple cartridge replacement

3-8CHAPTER3SPECIAL FUNCTIONS Dual page copyingThe DUAL PAGE COPY feature produces separate copies of twodocuments placed side by side on the document

Seite 123

3-9CHAPTER3SPECIAL FUNCTIONS Dual page copying5Ensure that the desired tray is selected.6Enter the desired number of copies.7Press the START ( ) key.

Seite 124 - Staple jam removal

3-10CHAPTER3The MULTI SHOT function is used to copy several originals, collectively ina specified order, onto one sheet.●When the MULTI SHOT is select

Seite 125

3-11CHAPTER35Press the “MULTI SHOT” key on the touch panel.●The function setting screen for MULTI SHOT will appear.6Select the number of originals to

Seite 126 - SF-S15 20-bin sorter

3-12CHAPTER39Press the upper “OK” key.10Enter the desired number of copies.11Press the START ( ) key.●If the document feeder is used, copying will sta

Seite 127

3-13CHAPTER3COVERSSPECIAL FUNCTIONS CoversThe COVERS mode is used to place covers on the front, back, or boththe front and back of multipage document

Seite 128

3-14CHAPTER35Select cover placement.●Select “FRONT”, “BACK” or “FRONT+BACK” on the touchpanel.6Indicate whether the front cover sheets are copied on o

Seite 129

3-15CHAPTER3TRANSPARENCY FILM WITH INSERT SHEETSSPECIAL FUNCTIONS Transparency film with insert sheetsWhen copying onto transparency film, insert she

Seite 130

1-1CHAPTER1CHAPTER 1GETTING STARTEDThis chapter describes the basic information on the use of this copier. Page●●

Seite 131 - FINISHER (AR-FN2)

3-16CHAPTER34Indicate whether the insert sheets are copied on or not.●Select “YES” or “NO” on the touch panel.5Press the upper “OK” key.6Load transpar

Seite 132

3-17CHAPTER3SPECIAL FUNCTIONS Pamphlet copyPAMPHLET COPYOriginals(2-sided)Originals(1-sided)READY TO COThe PAMPHLET COPY function is use

Seite 133

3-18CHAPTER33Press the “PAMPHLET COPY” key on the touch panel.● The setting screen for PAMPHLET COPY will appear.● Depending on installation of an opt

Seite 134

3-19CHAPTER37Check the copy paper selection.●When the desired paper size is not selected, touch the desiredpaper tray on the touch panel then the AUTO

Seite 135

3-20CHAPTER3SPECIAL FUNCTIONS Image editing functionsThe JOB BUILD function allows copying of multipage documents containingup to 120 pages (the limi

Seite 136

3-21CHAPTER3SPECIAL FUNCTIONS Image editing functionsIMAGE EDITING FUNCTIONSREADY TO COREADY TO COPY. SPECIAL MODESMARGIN SHIFTMULTI SHOTPAMPHLET COP

Seite 137

3-22CHAPTER3IMAGE EDITING FUNCTIONSSPECIAL FUNCTIONS Image editing functionsWhen the original and copy paper are of different sizes, CENTRING isused

Seite 138

3-23CHAPTER3SPECIAL FUNCTIONS Image editing functionsIMAGE EDITING FUNCTIONS2Press the “PAPER SELECT” key on the touch panel andselect the desired pa

Seite 139

3-24CHAPTER3IMAGE EDITING FUNCTIONSSPECIAL FUNCTIONS Image editing functionsREPEAT COPYREPEAT COPY is used to produce repeated images of an original

Seite 140

3-25CHAPTER3IMAGE EDITING FUNCTIONSSPECIAL FUNCTIONS Image editing functions2Select the desired copy paper size.●Press the “PAPER SELECT” key on the

Seite 141

1-2CHAPTER1INSTALLATION REQUIREMENTSTo ensure safety and proper machine performance, please note the followingbefore initial installation and whenever

Seite 142 - LARGE CAPACITY TRAY (AR-LC1N)

3-26CHAPTER3IMAGE EDITING FUNCTIONSSPECIAL FUNCTIONS Image editing functions7Select a type of border line.●Select the solid line, broken line or no b

Seite 143 - Loading copy paper

3-27CHAPTER3SPECIAL FUNCTIONS Image editing functionsIMAGE EDITING FUNCTIONSREADY TO COThe B/W REVERSE feature is used to reverse black and white are

Seite 144

3-28CHAPTER3IMAGE EDITING FUNCTIONSSPECIAL FUNCTIONS Image editing functions5Press the upper “OK” key.6Make all other desired copier selections and e

Seite 145

3-29CHAPTER3IMAGE EDITING FUNCTIONSSPECIAL FUNCTIONS Image editing functionsBINDING CHANGEThis function rotates the image of originals of the second

Seite 146 - STAND/500-SHEET PAPER DRAWER

3-30CHAPTER31Place the originals in the document feeder tray or on thedocument glass.2Press the 2-SIDED COPY key and select the 1-sided to 2-sided cop

Seite 147

3-31CHAPTER36Press the upper “OK” key.7Make all other desired copier selections and enter thedesired number of copies.8Press the START ( ) key.●If the

Seite 148

3-32CHAPTER3These functions are selected by pressing the “TEXTSTAMP” key on the SPECIAL MODES screen and thenselecting from the “TEXT STAMP” menu.●The

Seite 149 - DUAL TRAY OUTPUT UNIT

3-33CHAPTER33Press the “TEXT STAMP” key on the touch panel.●The TEXT STAMP menu will appear.4Press the “DATE” key on the touch panel.●The setting scre

Seite 150 - Specifications

3-34CHAPTER38Select the print direction.●If the PAMPHLET COPY function is used with this function, theportrait orientation ( ) must be selected.9Press

Seite 151 - CHAPTER 8

3-35CHAPTER3SELECT STAMPThe SELECT STAMP function adds a selected stamp such as“Confidential” and “Urgent” to the copies. The stamp will be printed in

Seite 152 - ENTER KEY OPERATOR CODE

1-3CHAPTER1CAUTIONS1. Do not touch the photoconductive drum. Scratches orsmudges on the drum will cause dirty copies.2. The fusing unit is extremely h

Seite 153 - KEY OPERATOR CODE NUMBER

3-36CHAPTER3MPESS POSITIONCANCELOKOK5Select the desired stamp to be printed.●The selected stamp will be highlighted.6Select the pages to be stamped.●I

Seite 154

3-37CHAPTER310Press the lower “OK” key.●The TEXT STAMP menu will appear again.11Select the print direction.●If the PAMPHLET COPY function is used with

Seite 155

3-38CHAPTER31Place the originals in the document feeder tray or on thedocument glass.2Press the SPECIAL MODES key.●The SPECIAL MODES screen will appea

Seite 156

3-39CHAPTER34Press the “WATERMARK” key on the touch panel.●The setting screen for WATERMARK will appear.5Select the desired watermark to be printed.●T

Seite 157

3-40CHAPTER39Press the lower “OK” key.●The TEXT STAMP menu will appear again.10Select the print direction.●If the PAMPHLET COPY function is used with

Seite 158

3-41CHAPTER3-1- 1/5 1The PAGE NUMBER function adds page numbers to the copies.●The page number format can be selected from three types.●The page numbe

Seite 159 - ACCOUNT CONTROL

3-42CHAPTER34Press the “PAGE NUMBER” key on the touch panel.●The setting screen for PAGE NUMBER will appear.5Select the desired page number format.●Th

Seite 160 - Account Number Control

3-43CHAPTER39Press the upper “OK” key.10Make all other desired copier selections and enter thedesired number of copies.11Press the START ( ) key.●If t

Seite 161 - To change an account number

3-44CHAPTER3SPECIAL FUNCTIONS Tandem copyTANDEM COPY1Ensure that the two copiers are connected through thetandem-connection cable and they have been

Seite 162 - To set a limit

3-45CHAPTER3SPECIAL FUNCTIONS Tandem copy12 34 567890CPCLEARPROGRAMAUDIT CLEARINTERRUPTCCLEARINTERRUPTCACLEAR ALLSTARTTRANSPARENCYINSERTSDUAL PAGECOP

Seite 163 - Account Number Security

1-4CHAPTER1CAUTIONSGETTING STARTED CautionsFor Europe:CLASS 1 LASER PRODUCTLASER KLASSE 1LUOKAN 1 LASERLAITEKLASS 1 LASERAPPARATCAUTIONINVISIBLE LASE

Seite 164 - EXPOSURE ADJUSTMENT

3-46CHAPTER3SPECIAL FUNCTIONS Setting reviewThe current settings of copier functions can be displayed on the touchpanel.SETTING REVIEW1Press the REVI

Seite 165

4-1CHAPTER4CHAPTER 4SUPPLIESThis chapter describes the supplies for this copier such as paper andtoner. Page●●●●

Seite 166 - Erase Width Adjustment

4-2CHAPTER4PAPER Types and sizes of copy paperSize Weight Capacity Special paper(80 g/m2 (21lb.)paper)Paper trays A5 to A3 56 to 105 g/m2500 sheets1 a

Seite 167 - Stream Feeding Mode

4-3CHAPTER4SUPPLIES PaperLoading paper in paper trays 1 and 21Gently lift and pull out the paper tray.2Only use paper within the Sharp specification

Seite 168 - SETTING

4-4CHAPTER4PAPERChanging the copy paper size in the tray1Gently lift and pull out the paper tray until it stops.2Adjust the paper size indicator to ma

Seite 169 - Rotation Copy Setting

4-5CHAPTER4The message “(TONER SUPPLY IS LOW. PRESS FORGUIDANCE.)” will appear in the message display before the tonersupply is completely empty. If

Seite 170 - Size Setting for [EXTRA]

4-6CHAPTER44Place the new toner cartridge with the tabs in thenotches as shown.5Slide the toner cartridge along the guides over the tonerhopper.6Hold

Seite 171 - TIMER SETTINGS

4-7CHAPTER41Open the toner collecting container cover.●Push once on the door to unlatch and open it.2Disengage and remove the container from the copie

Seite 172 - Noise Level Reduce Mode

4-8CHAPTER4SUPPLIES Storage of suppliesGENUINE SUPPLIESSTORAGE OF SUPPLIESThe supplies of this copier replaced by the user include copy paper,toner,

Seite 173 - SET THE TIME FOR MESSAGES

5-1CHAPTER5CHAPTER 5COPIER TROUBLE?This chapter describes how to remove misfed originals and paper andother common trouble remedies.

Seite 174 - ENABLE/DISABLE SETTINGS

1-5CHAPTER1POWER ON AND OFFThe power switch is located on the left side of the copier. When thepower switch is turned to the “ON” position, the messag

Seite 175 - Disabling of Duplex Copying

5-2CHAPTER5MISFEED REMOVALWhen a misfeed occurs, the copier will stop.The message “A MISFEED HAS OCCURRED. CLEARINDICATED AREA. PRESS FOR RECOVERYIN

Seite 176 - Disabling of PC/Modem Access

5-3CHAPTER5Misfeed in the RADFWhen the RADF misfeeds an original sheet, the copier will stop and themisfeed message will appear.An original misfeed ma

Seite 177

5-4CHAPTER5COPIER TROUBLE? Misfeed removalMISFEED REMOVALMisfeed in the bypass tray1Gently pull the misfed paper out.2Open and close the front cover

Seite 178 - OTHER PROGRAMS

5-5CHAPTER5COPIER TROUBLE? Misfeed removalMISFEED REMOVALMisfeed in paper trays 1 and 21Open the right side cover.●Hold the handle and gently open th

Seite 179 - KEY OPERATOR ASSISTANCE CALL

5-6CHAPTER5MISFEED REMOVALCOPIER TROUBLE? Misfeed removalMisfeed in the transport area1Open the front cover.2Remove the misfed paper.1Turn the transp

Seite 180 - CHAPTER8

5-7CHAPTER5MISFEED REMOVALCOPIER TROUBLE? Misfeed removal3Turn the transport lever back into place.3Close the front cover.●Confirm that the misfeed d

Seite 181 - FACTORY SETTING

5-8CHAPTER5MISFEED REMOVAL3Remove the misfed paper.If the misfed paper is in the inner part of the exit area:1Turn roller rotating knob B in the direc

Seite 182 - CINSE1954FC51

5-9CHAPTER5MISFEED REMOVALCOPIER TROUBLE? Misfeed removal5Close the front cover.●Confirm that the misfeed display is cleared.Misfeed in the duplex mo

Seite 183

5-10CHAPTER5Paper feed area open/close lever3Remove the misfed paper from the section below the exit area.3Close the exit area cover.4Open and close t

Seite 184 - SHARP ELECTRONICS (U.K.) LTD

5-11CHAPTER5MAINTENANCE REQUIREDWhen the message “READY TO COPY. (MAINTENANCE REQUIRED)”appears in the message display, service by an authorised Sharp

Kommentare zu diesen Handbüchern

Keine Kommentare