R-210ATABLE OF CONTENTSPageCAUTION, MICROWAVE RADIATION ...
R-210A8CARRY OUT 3D CHECKS.Isolate the magnetron from the high voltage circuit by removing all leads connected to the filamentterminal.To test for an
R-210A91000g1000g1000gT1˚CT2˚CHeat up for 62 sec.Initial temperature...
R-210A10TEST PROCEDURESPROCEDURELETTERCOMPONENT TESTCAUTION: 1˚C CORRESPONDS TO 60 WATTS. REPEAT MEASUREMENT IF THE POWER ISINSUFFICIENT.1 l 1 l(T1 C
R-210A11TEST PROCEDURESPROCEDURELETTERCOMPONENT TESTCARRY OUT 3D CHECKS.If the fuse 13A is blown when the door is opened, check the 1st latch switch,
R-210A12TEST PROCEDURESPROCEDURELETTERCOMPONENT TESTIf the fuse 13A is blown by incorrect door switching replace the defective switch(es) and the fuse
R-210A13COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDUREWARNING: Avoid possible exposure to microwave energy. Please follow the instructionsbelow before
R-210A14HIGH VOLTAGE COMPONENTS REMOVAL(HIGH VOLTAGE CAPACITOR, HIGH VOLTAGE RECTIFIER ASSEMBLY AND H.V. FUSE)To remove the components, proceed as fol
R-210A15POWER SUPPLY CORD REPLACEMENTRemoval1. CARRY OUT 3D CHECKS.2. Disconnect the wire leads from the power supply cord.3. Remove the one (1) screw
R-210A16CAUTION:• Do not re-use the removed fan blade be-cause the hole (for shaft) may be lagerthan normal.9. Remove the two (2) screws holding the f
R-210A17flange of the oven front face.2. With the door closed, adjust latch hook by moving itback and forth and up and down. In and out play of thedoo
R-210A18ture, light or sensing of gentle warm air movementaround oven door is not abnormal and do not ofthemselves indicate a leakage of microwave en-
R-210A19MICROWAVE MEASUREMENTAfter adjustment of door latch switches, monitor switchand door are completed individually or collectively, thefollowing
R-210A20NOTE: " " indicates components with potential above 250V.SCHEMATICNOTE: CONDITION OF OVEN1. DOOR CLOSED.2. TIMER KNOB AT "0&quo
R-210A21645123645123ABCDEFGHABCDEFGHFigure S-1. Pictorial DiagramWHTREDGRYWHTGRYREDBLKREDORGBLUGRYREDTEMP. FUSE120˚C (OVEN)1ST LATCHSWITCHMONITORSW
R-210A22PARTS LISTNote: The parts marked "∆" may cause undue microwave exposure.The parts marked "*" are used in voltage more than
R-210A23Note: The parts marked "∆" may cause undue microwave exposure.The parts marked "*" are used in voltage more than 250V.REF.
R-210A24645123645123ABCDEFGHABCDEFGHOVEN AND CABINET PARTS7-84-191-51-104-134-34-24-151-137-21-97-92-16-66-54-127-77-77-77-77-94-54-204-141-47-87-2 4-
R-210A25645123645123ABCDEFGHABCDEFGHDOOR PARTSMISCELLANEOUSCONTROL PANEL PARTS5-35-23-23-43-37-13-53-11-15-45-56-45-75-75-65-85-15-7Actual wire harnes
R-210A26'97SHARP CORP. (11K0.100E) Printed in Japan
R-210A1SERVICE MANUALSHARP CORPORATIONOSAKA, JAPANMICROWAVE OVENR-210AGENERAL IMPORTANT INFORMATIONThis Manual has been prepared to provide Sharp Corp
R-210A2PRODUCT DESCRIPTIONSPECIFICATIONITEM DESCRIPTIONPower Requirements 110 Volts60 HertzSingle phase, 2 wirePower Consumption 1.1 KWPower Output 70
R-210A3APPEARANCE VIEW1. Ventilation openings2. Oven lamp3. Door hinges4. Door safety latches5. See through door6. Door seals sealing surfaces7. Coupl
R-210A4OPERATION SEQUENCE7-1. When the oven door is opened during or after thecycle of a cooking program, the 1st latch switch and2nd latch switch mus
R-210A5FUNCTION OF IMPORTANT COMPONENTSDOOR OPEN MECHANISMThe door can be opened by pushing the open button on thecontrol panel. When the open button
R-210A6Note: The ON/OFF time ratio does not exactly corre-spond to the percentage of microwave power,because approx. 2 seconds are needed for heat-in
R-210A7MAGNETRONPOWER TRANSFORMERH.V. RECTIFIER ASSEMBLYHIGH VOLTAGE CAPACITOR1ST. LATCH SWITCH2ND. LATCH SWITCHMONITOR SWITCHTEMPERATURE FUSE 120˚C (
Kommentare zu diesen Handbüchern