Sharp RK-12S30 Bedienungsanleitung PDF herunterladen

PART NAME

EXHAUST DUCT BACK

PDVC-B107WRWZ

EXHAUST DUCT UPPER

PDVC-B105WRWZ

DIVIDE PLATE L

PSKR-A486WRWZ

DIVIDE PLATE R

PSKR-A487WRWZ

RECTIFIER PLATE L

PSKR-A484WRWZ

EXHAUST DUCT LEFT

PDVC-B108WRWZ

EXHAUST DUCT RIGHT

PDUC-B117WRWZ

EXHAUST DUCT BOTTOM

PDVC-B106WRWZ

FRAME ASSEMBLY

FDEC-A004WRKZ

SCREW(A)

XHTS740P08000

SCREW(B)

XMMS841P13000

SCREW(C)

XMSS827P25000

REAR SPACER

PSPAFA003WRWZ

CUSHION

/8" x 16",

15 mm x 405 mm

PCUS-A245WRPZ

CUSHION

/4" x 24

/8",

5 mm x 618 mm

PCUS-A247WRPZ

CUSHION

" x 27

30 mm x 689 mm

PCUS-A249WRPZ

CUSHION

/4" x 12",

5 mm x 305 mm

PCUS-A251WRPZ

CUSHION

/4" x 15",

5 mm x 382 mm

PCUS-A253WRPZ

INSTALLATION INSTRUCTIONS

BUILT-IN KIT MODEL

IMPORTANT: This Built-In Kit is designed for use with Sharp SuperSteam Ovens specifying a RK-12S30

Built-In Kit on the rating label on the front of the oven.

The cabinet or wall opening must be within the following dimensions:

HEIGHT 19" to 19

/8" (482 mm - 486 mm)

WIDTH 28" to 28

/4" (710 mm - 719 mm)

DEPTH 23

/4" minimum (509.5 mm minimum)

The completed built-in kit frame assembly dimensions:

HEIGHT 19

/2" (495mm)

WIDTH 30" (762mm)

NOTE: The bottom of the cut-out opening for built-in use must be 36 inches (915 mm) or higher from the floor.

PLEASE READ THESE INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION!

The electrical requirements for this oven are 120 volts, 15 amps. The oven has a 5-15 plug

and requires a 5-15 receptacle.

RK-12S30

Q'TY

* For walls other than wood, you may need screws appropriate for that

wall to install the frame.

Be sure to DISCONNECT THE PLUG of the oven from the electrical

outlet before installing the oven and kit.

* Because the kits are metal, due caution should be used in handling

and installation to avoid the possibility of injury.

PROVIDED PARTS

SCREW (C) - LONG

EXHAUST DUCT BOTTOM

EXHAUST DUCT

BACK

EXHAUST

DUCT UPPER

EXHAUST

DUCT

RIGHT

DIVIDE PLATE L

DIVIDE PLATE R

FRAME

ASSEMBLY

RECTIFIER

PLATE L

EXHAUST

DUCT LEFT

REAR SPACER

SCREW (B) - MIDDLESCREW (A) - SHORT

TINSEB184WRRZ-D92

Printed in Thailand

RK12S30 2nd 09.1.14, 11:01 AM1

1 2 3 4 5 6 7 8

Inhaltsverzeichnis

Seite 1 - RK-12S30

1PART NAMEEXHAUST DUCT BACKPDVC-B107WRWZEXHAUST DUCT UPPERPDVC-B105WRWZDIVIDE PLATE LPSKR-A486WRWZDIVIDE PLATE RPSKR-A487WRWZRECTIFIER PLATE LPSKR-A48

Seite 2 - PREPARATION

2PREPARATIONFollow the directions from 1 to 5 to attach cushions to some parts.1. EXHAUST DUCT UPPERRemove the backing paper from each CUSHION 1.Attac

Seite 3 - 5. DIVIDE PLATE R

33. EXHAUST DUCT BOTTOMRemove the backing paper from CUSHION 3.Attach the CUSHION 3 to the EXHAUST DUCT BOTTOM as shown in the Illustration below.* St

Seite 4 - " (710 mm - 719 mm)

4STEP 1: CABINET OR WALL OPENINGProvide an opening in the wall or cabinet shown in Figure 1.The depth should be minimum 23 1/4" (590.5 mm). The

Seite 5 - RK12S30 2nd 09.1.7, 5:19 PM5

5STEP 3: EXHAUST DUCT BOTTOM INSTALLATION1 Place the oven onto the EXHAUST DUCT BOTTOM, lowering the 4 feet of the oven onto the projectionsat the 4 c

Seite 6 - RK12S30 2nd 09.1.8, 4:21 PM6

6STEP 5: INSTALLATION OF REAR SPACER and EXHAUST DUCT UPPER1 Attach RECTIFIER PLATE L to inside of EXHAUST DUCT UPPER with 4 SCREWS (A) as shown in Fi

Seite 7 - STEP 8: OVEN INSTALLATION

7STEP 8: OVEN INSTALLATIONCAUTION: Never hold the handle when moving the oven. Two persons are required to install the oven.1 Establish center line of

Seite 8 - RK12S30 2nd 09.1.7, 5:19 PM8

84 Secure EXHAUST DUCT BOTTOM to the shelf with 2 SCREWS (B) as shown in Figures 8-B.STEP 9: FRAME ASSEMBLY INSTALLATION1 Attach FRAME ASSEMBLY and ti

Kommentare zu diesen Handbüchern

Keine Kommentare

Sharp RK-12S30 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Nein Sharp RK-12S30 herunter. Sharp RK-12S30 User's Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein Sharp RK-12S30