Sharp JH-1600E Spezifikationen

JH-1600EINSTALLATION &OPERATION MANUALSolar Power InverterMODELPage• IMPORTANT SAFETY INSTRUCTIONS ... 1Conventions U

8(3) Place the JH-1600E on the mounting bracket. Key holes located on the upper side and middle side of the inverter unit are for hanging the unit on

9Wiring Solar Power Inverter• All of the procedure must be completed by a qualified electrician.• Wiring the solar power inverter and the DC disconnec

10Before wiringAC Circuit breakerThis breaker must be sized to handle the rated maximum output voltage and current of the inverter. (Please refer to t

11Removing the Front PanelRemove the front panel of the solar power inverter.(1) Remove the 4 screws from the lower part of the front panel of the sol

12Solar Power Inverter Wiring OverviewGeneral wiring stepsThere are four main steps in the wiring of the inverter:(1) Grounding the PV array (see your

13Connecting to DC DisconnectThis section describes the connection between the solar power inverter and the DC disconnect from the PV string.Follow al

14(3) Connect the black wire to the positive terminal of the terminal block, and tighten the screw firmly to clamp the wire.(4) Attach a forked spade

15Connecting to AC DisconnectThis section describes the connection between the solar power inverter and the AC disconnect. The wires needed are the AC

16(2) Connect one wire to the N terminal of the AC terminal block, and tighten the screw firmly to clamp the wire.Connect the other wire (after perfor

18Test RunChecking the PV Array DC VoltageTo check the PV array DC voltage:(1) Uncover the PV arrays and expose them to full sunlight. The sunlight mu

This Sharp product is warranted against faults in materials and manufacture for a period of sixty (60) months from the date of original purchase.Such

19Monitoring the InverterDisplay PanelStatus Indicator LightsThe inverter is equipped with two status indicator lights (LEDs) located above the front

20Monitoring the Front DisplayDisplay FlowchartPress"SELECT".Displays output power instantaneously.Displays today watt-hour.Displays life ki

21Islanding ProtectionThe inverter will shut down when the power from the grid becomes abnormal or fails. This will provide safety to the people worki

22Emergency StopTurn off the AC disconnect and the DC disconnect when you execute an emergency stop of the inverter.RestartTurn on the AC disconnect f

23SpecificationElectrical SpecificationEnvironment SpecificationMechanical SpecificationInput JH-1600EAbsolute maximum array open circuit voltage 350

25Checking Output PowerThe output power of the last 7 days (the current day is included) can be checked.Press "ENT" and "SEL" in t

26Memo

TiNSJ0546SNZZ1 Huntingwood Drive, Huntingwood, NSW 2148.by phone on: 1300 135 022or by fax on: 1300 727 717WEB sitehttp://www.sharp.net.au/

1IMPORTANT SAFETY INSTRUCTIONSSAVE THESE INSTRUCTIONSThis manual contains important safety instructions that shall be followed during the installation

21. PV* Module / 2. Mounting Structure3PV ArrayJH-1600E3. Wiring Cables5. Solar Power InverterConverts solar energy to electric power. PV modules are

3DimensionsSolar Power Inverter408440±5348141(Unit: mm)

4Mounting BracketUnpacking Carton BoxBefore installation, make sure all the items listed below are included within the carton box.• Bracket ...

5InstallationPlanning the InstallationThe following issues need to be considered when planning for an installation using the inverter. See the specifi

6Installing Solar Power InverterInverter failure due to improper installation will void the inverter warranty.Consider the following when determining

7Mount the Solar Power InverterMake sure the supporting surface is strong enough to handle 50 kg.Wall Mount Bracket DimensionsThe dimensions of the mo