Sharp UP-810F Bedienungsanleitung

CONTENTSParts marked with "!" are important for maintaining the safety of the set. Be sure to replace these parts with specifiedones for mai

UP-810F/820N/820F(U) SRV MODE PROGRAMMING (“SETTING”)3 – 3DEVICE CONFIG - 6. REPORT PRINTERDEVICE CONFIG - 7. VALIDATION (VP)DEVICE CONFIG - 8. KP#1 -

UP-810F/820N/820F(U) SRV MODE PROGRAMMING (“SETTING”)3 – 4DEVICE CONFIG - 10. BCR (SCANNER)* ER-A61HS1 setting : “BAUD RATE = 4800 bps” , “DATA BITS =

UP-810F/820N/820F(U) SRV MODE PROGRAMMING (“SETTING”)3 – 52. SYSTEM PRESET (SRV-MODE PROGRAMMING)[JOB#801] : MRS=0000 (Not used)[JOB#802] : MRS=000080

UP-810F/820N/820F(U) SRV MODE PROGRAMMING (“SETTING”)3 – 6903-B: 1. Symbol of scale entry2. Printing Gift Card No. at Gift Purchase Active and Reload9

UP-810F/820N/820F(U) SRV MODE PROGRAMMING (“SETTING”)3 – 7905-D: 1. Tax method (canadian tax)[JOB#906] : MRS=0030906-A: 1. Printing of DEPT. /PLU code

UP-810F/820N/820F(U) SRV MODE PROGRAMMING (“SETTING”)3 – 8907-C: 1. In case of all server or transaction CCD, X report before CCDentry2. Minus departm

UP-810F/820N/820F(U) SRV MODE PROGRAMMING (“SETTING”)3 – 9[JOB#911] : MRS=0000911-A: 1. Fraction treatment911-B: 1. C/D (Check digit) check of UPC (EA

UP-810F/820N/820F(U) SRV MODE PROGRAMMING (“SETTING”)3 – 10913-D: 1. Drawer closing2. Error system3. Key touch sound[JOB#914] : MRS=1100914-A: 1. Rece

UP-810F/820N/820F(U) SRV MODE PROGRAMMING (“SETTING”)3 – 11916-B: 1. Finalization by charge (credit) when ST t 02. Food stamp/Cash benefit subtotal e

UP-810F/820N/820F(U) SRV MODE PROGRAMMING (“SETTING”)3 – 12917-D: 1. Printing of total tax on X/Z report2. Printing of gross manual tax and refund man

UP-810F/820N/820F (U) LEAD-FREE SOLDER LEAD-FREE SOLDERThe PWB’ s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and

UP-810F/820N/820F(U) SRV MODE PROGRAMMING (“SETTING”)3 – 13919-C: 1. PB entry2. Amount printing when PLU unit price is zero919-D: 1. Conversion SBTL p

UP-810F/820N/820F(U) SRV MODE PROGRAMMING (“SETTING”)3 – 14923-D: 1. Polling cycle (second)Ex:When input D = 5, the master waits 5 sec., and then the

UP-810F/820N/820F(U) SRV MODE PROGRAMMING (“SETTING”)3 – 15[JOB#927] : MRS=0000 (Not used)[JOB#928] : MRS=0060928-A: 1. Printing of slip logo text928-

UP-810F/820N/820F(U) SRV MODE PROGRAMMING (“SETTING”)3 – 16[JOB#987] : MRS = 0000987-A: Not used (Fixed at “0”)987-B: 1. Age limit function to be over

UP-810F/820N/820F(U) SRV MODE PROGRAMMING (“SETTING”)3 – 1715 X X X/QTY No16 Sub total SUB TOTAL SUB_TOTAL Yes17 Mode MODE MODE Yes18 CURSOR UP UP b N

UP-810F/820N/820F(U) SRV MODE PROGRAMMING (“SETTING”)3 – 1899 Price1 PRICE SFT1 P1 Yes100 Price2 PRICE SFT2 P2 Yes101 Price3 PRICE SFT3 P3 Yes102 Pric

UP-810F/820N/820F(U) SRV MODE PROGRAMMING (“SETTING”)3 – 19191 AUTO58 AUTO58 AUTO58 Yes192 AUTO59 AUTO59 AUTO59 Yes193 AUTO60 AUTO60 AUTO60 Yes194 AUT

UP-810F/820N/820F(U) SRV MODE PROGRAMMING (“SETTING”)3 – 20277 Message3 (For KP) MESSAGE3 MSG3 Yes278 Message4 (For KP) MESSAGE4 MSG4 Yes279 Message5

UP-810F/820N/820F(U) SRV MODE PROGRAMMING (“SETTING”)3 – 21361 FUNCTION MENU 17FUNC MENU 17FUNC_MENU17No362 FUNCTION MENU 18FUNC MENU 18FUNC_MENU18No3

UP-810F/820N/820F(U) SRV MODE PROGRAMMING (“SETTING”)3 – 22[TOUCH KEY DISPLAY]Touch key (2 x 6 character) is displayed by centering as follows.Symbol’

UP-810F/820N/820F (U) LEAD-FREE SOLDERMAJOR KEYS USED IN THE SRV MODEThe following major keys are used in the SRV mode.KEYBOAD LAYOUT<UP-820N>

UP-810F/820N/820F(U) SRV MODE PROGRAMMING (“SETTING”)3 – 236. PROGRAMMING OF THE Z CONTER [JOB#930] Z REPORT COUNTER : Z COUNTER[JOB#942] GRAND TOTAL

UP-810F/820N/820F(U) SRV MODE PROGRAMMING (“SETTING”)3 – 24* :The files which are created or erased by the entry of the group No.**: For individual er

UP-810F/820N/820F(U) SRV MODE PROGRAMMING (“SETTING”)3 – 25FILE CONTENTSTa bl eNo.File NameRecord BLOCKLabel SizeData SizeMRSMAX #1 MRS MAX #2Normal k

UP-810F/820N/820F(U) SRV MODE PROGRAMMING (“SETTING”)3 – 2647 DYNAMIC UPC PRESET 0 **** 01 7+24848 FLAG 0 **** 47 0 1 0 249 PRICE1 0 ****

UP-810F/820N/820F(U) SRV MODE PROGRAMMING (“SETTING”)3 – 2794 SERVER TRNSACTION LABEL 160 160 15 15 91 2 095 DAILY 160 160 92 15 15 91 0 996

UP-810F/820N/820F(U) SRV MODE PROGRAMMING (“SETTING”)3 – 28141 SCROLL MESSAGE TEXT 1 1 1 1 1 64142 KP PRESET 9 9 1 1 1 4143 KP TEXT 9 9 142 1 1 0 1

UP-810F/820N/820F(U) SRV MODE PROGRAMMING (“SETTING”)3 – 29187 SCHEDULE PFLD2 BUFFER 0 **** 175 0 1 0 150188 SCHEDULE PFLD3 BUFFER 0 **** 17

UP-810F/820N/820F(U) SRV MODE PROGRAMMING (“SETTING”)3 – 30234 PLU (Combo) consol (Price1-6) 0 **** 15 0 6 0 9235 PLU (Combo) receive (Price1-6) 0 ***

UP-810F/820N/820F(U) SRV MODE PROGRAMMING (“SETTING”)3 – 31#1 : Same as the number of record of table no. N#2 : The number of table is same as the num

UP-810F/820N/820F(U) SRV MODE PROGRAMMING (“SETTING”)3 – 32[JOB#990]SSP INPUT[JOB#991]SSP EDIT[JOB#992]SSP ALL CLEAR[JOB#993]SSP IND. CLEAR12.MAINTENA

UP-810F/820N/820F (U) TOUCH PANEL CALIBRATION, MASTER RESET AND PROGRAM RESET1 – 1CHAPTER 1. TOUCH PANEL CALIBRATION, MASTER RESET AND PROGRAM RESET1.

UP-810F/820N/820F(U) SRV MODE PROGRAMMING (“SETTING”)3 – 33PLU OTHER PROGRAMMINGCOMBO MEAL TABLES(-)Print station OUTPUT KP No.1DISABLE/ENABLE ENABLEP

UP-810F/820N/820F(U) SRV MODE PROGRAMMING (“SETTING”)3 – 34%Item (text) Range/DetailMRS defaultRate RATE DISABLE/ENABLE ENABLEText TEXT DISABLE/ENABLE

UP-810F/820N/820F (U) SRV MODE PROGRAMMING (“IRC SETTING”)4 – 1CHAPTER 4. SRV MODE PROGRAMMING (“IRC SETTING”)1. MANUAL CLEAR AND RESETThis operation

UP-810F/820N/820F (U) SRV MODE PROGRAMMING (“IRC SETTING”)4 – 2Entry [TERMINAL NO.] WINDOW.3The POS is changed from standalone POS to inline satellite

UP-810F/820N/820F (U) SRV MODE PROGRAMMING (“IRC SETTING”)4 – 3Entry [TERMINAL NO.] WINDOW.3The POS is changed from standalone POS to inline satellite

UP-810F/820N/820F (U) SRV MODE PROGRAMMING (“DOWN LOAD”)5 – 1CHAPTER 5. SRV MODE PROGRAMMING (“DOWN LOAD”)The preset data of master machine is downloa

UP-810F/820N/820F (U) SRV MODE PROGRAMMING (“SD CARD MODE”)6 – 1CHAPTER 6. SRV MODE PROGRAMMING (“SD CARD MODE”)In ECR, SD CARD is the tool for provid

UP-810F/820N/820F (U) SRV MODE PROGRAMMING (“SD CARD MODE”)6 – 23. LIST OF FOLDEREJTLOG("x" can be used numeric characters.)SHARP ECR xxxxxx

UP-810F/820N/820F (U) SRV MODE PROGRAMMING (“SD CARD MODE”)6 – 34. SALES DATA (SAVING) (PGM2 & SRV MODE) All sales data (Daily and term) are saved

UP-810F/820N/820F (U) SRV MODE PROGRAMMING (“SD CARD MODE”)6 – 43) Create the “STATUS.REC” file in new sub-folder when all files aresaved completely.4

UP-810F/820N/820F (U) TOUCH PANEL CALIBRATION, MASTER RESET AND PROGRAM RESET1 – 2[Master resetting]Master resetting 1, 2 and 3 can be accomplished by

UP-810F/820N/820F (U) SRV MODE PROGRAMMING (“SD CARD MODE”)6 – 55) In case of “SAVE & CLEAR” job, after saving T-LOG data to SD cardthe T-LOG data

UP-810F/820N/820F (U) SRV MODE PROGRAMMING (“SD CARD MODE”)6 – 6(*1) The contents of each file are same as the communication data of“ONLINE FUNCTION”.

UP-810F/820N/820F (U) SRV MODE PROGRAMMING (“SD CARD MODE”)6 – 712.FOLDER READINGSD in the folder screen to list of display.“4 FOLDER READING” is sele

UP-810F/820N/820F (U) SRV MODE PROGRAMMING (“SD CARD MODE”)6 – 814.PRINT The message is printed on JOURNAL onlyThe MESSAGEs are fixed in ROM.Print NOT

UP-810F/820N/820F (U) SRV MODE PROGRAMMING (“SD CARD MODE”)6 – 915.ERROR MESSAGE LIST(O : Used, — : Not used)No. Description MESSAGE DISPLAY PRINT 1 S

SHARP CORPORATIONInformation and Communication Systems GroupCS Promotion CenterYamatokoriyama, Nara 639-1186, Japan2008 May Printed in Japan tCOPYRIGH

UP-810F/820N/820F (U) READING OF SRV MODE PROGRAM2 – 1CHAPTER 2. READING OF SRV MODE PROGRAM[How to enter SRV mode]Operator can enter the SRV-mode by

UP-810F/820N/820F (U) READING OF SRV MODE PROGRAM2 – 22. [DEVICE CONFIG]* 1: PROGRAMa: Data Bit 7Bits/8Bitsb: Stop Bit 1Bits/2Bits3. [HOME MENU DI

UP-810F/820N/820F(U) SRV MODE PROGRAMMING (“SETTING”)3 – 1CHAPTER 3. SRV MODE PROGRAMMING (“SETTING”)[JOB LIST]1. DEVICE ASSIGNMENT (CONFIG) [JOB #945

UP-810F/820N/820F(U) SRV MODE PROGRAMMING (“SETTING”)3 – 2DEVICE CONFIG - 2. JOURNAL PRINTERDEVICE CONFIG - 3. EXTERNAL JOURNAL* External Journal cann