Sharp AR-286 Bedienungsanleitung PDF herunterladen (Seite 4)

Trouble code

Description

Main

code

Sub

code

F1 11 Content Finisher 1 pusher motor trouble / Finisher

2 boomerang rotation abnormality

Detail Pusher motor trouble / Paddle solenoid

abnormality

Cause Motor lock / paddle solenoid operation

abnormality / boomerang rotation sensor

abnormality

Motor rpm abnormality

Motor overcurrent

Finisher control PWB abnormality

Check

and

remedy

Check the finisher motor operation, the

paddle solenoid operation with SIM 3-3

or check the boomerang rotation sensor

with SIM 3-2.

14 Content Finisher 2 stack tray abnormality

Detail Stack tray control sensor abnormality

Cause The paper surface sensor and the full stack

sensor do not turn on even when a certain

time is passed after starting the tray.

Check

and

remedy

Check the sensor operation with SIM 3-2.

15 Content Finisher 1 elevator motor trouble /

Finisher 2 stack tray motor lock

Detail Elevator motor trouble

Cause Motor lock

Motor rpm abnormality

Motor overcurrent

Finisher control PWB trouble

Check

and

remedy

Check the elevator motor operation with

SIM 3-3.

16 Content Staple sorter holding motor trouble

Detail During rotation of the holding motor, the

rotation pulse is not detected for 0.05sec

or more.

Cause Motor lock.

Motor rotation abnormality.

Overcurrent to motor

Sorter control PWB abnormality

Check

and

remedy

Check the holding motor operation with

SIM3-3.

17 Content ST pressure release HP trouble

Detail ST paper exit roller pressure release trouble

when turning on the power/initializing

Cause ST paper exit roller pressure release

clutch abnormality

ST paper exit roller pressure release

clutch HP sensor abnormality

Check

and

remedy

Stop the transport motor in SIM 3-3, turn

on the STORCL to check that the

pressure release roller operates.

Check the STORHP sensor with SIM 3-2.

18 Content Tray 3 paper exit paddler operation trouble

Detail Tray 3 paper exit paddler operation

trouble when turning on the

power/initializing

Cause Tray 3 paper exit paddler solenoid

abnormality

Tray 3 paper exit paddler HP sensor

abnormality

Finisher control PWB trouble

Check

and

remedy

Operate the transport motor with SIM 3-3

and turn on T3PDSL to check that tray 3

paddler operates.

Check T3PDHP sensor with SIM 3-2.

Trouble code

Description

Main

code

Sub

code

F1 50 Content Non-support trouble in automatic

detection of option connection (Sorter,

finisher)

Detail In automatic detection of option

connection, a non-support finisher or a

sorter is detected.

Cause A non-support finisher or a sorter is

connected to the copier.

Check

and

remedy

Check the finisher or the sorter.

80 Content Finisher power not supplied

Detail 24V power is not supplied to the finisher

PWB.

Cause Connector harness improper connection

or disconnection

Finisher control PWB trouble

Power unit trouble

Check

and

remedy

Check the sensor operation with SIM 3-2.

F2 00 Content Toner control sensor open

Detail Toner control sensor output open

Cause Connector harness trouble

Connector unconnected.

Check

and

remedy

Check connection of the toner control

sensor.

Check connection of the connector

harness with the main PWB.

Check for disconnection of the harness.

02 Content Toner motor connector unconnected

Detail Connection detection signal with toner

motor is OFF

Cause Connector harness defective

Connector disconnected

Check

and

remedy

Check toner motor connector for

connection.

Check connector harness to main PWB

for connection.

Check harness for broken wire.

31 Content Process control trouble (OPC drum

surface reflection rate abnormality)

Detail Usually the sensor gain is adjusted so

that the output is a certain value, by

reading the drum base surface with the

image density sensor before starting

process control.

However, a certain output is not obtained

by adjusting the sensor gain.

Cause Image density sensor defective

Check

and

remedy

Check process control sensor output with

SIM44-2. (Do not adjust)

If the result is far different from the

specified value, it suggests the sensor is

defective. Check the sensor and harness.

If the deviation is relatively small, check

the sensor and drum surface for

contamination.

AR-505

9 – 4 8/6/1999

1 2 3 4 5 6 7 8 9 10

Kommentare zu diesen Handbüchern

Keine Kommentare

Sharp AR-286 Bedienungsanleitung Seite 4

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kopierer Sharp AR-286