Sharp AR-FX12 Spezifikationen PDF herunterladen (Seite 28)

SENDING A FAX

2-8

 Quick On-line

When you use the automatic document feeder to send a multi-page document and there are no previously stored

jobs waiting or in progress (and the line is not being used), the machine dials the destination after the first page

is scanned and begins transmitting scanned pages while the remaining pages are being scanned. This

transmission method is called Quick On-line. The messages "SCANNING ORIGINAL." and "SENDING." both

appear until scanning of the final page is completed.

If the receiving party is busy, the transmission will switch to a memory transmission. (Refer to the following

section, "Storing transmission jobs (memory transmission)".)

 Storing transmission jobs (memory transmission)

When a document is sent from the document glass, or when the telephone line is in use, the document is scanned

into memory and then automatically transmitted after previously stored transmission jobs are completed. This

means that transmission jobs can be stored in memory by performing a transmission operation while the machine

is occupied with another transmission/reception operation. This is called memory transmission, and up to 97

(maximum of 50 on the AR-M351U/AR-M451U) jobs can be stored in memory at once, including the job currently

being executed. After transmission, the scanned document data is cleared from memory. (However, when the

document filing function is used, the scanned document image is stored in the machine's hard disk. For

information on managing stored images, see "Document filing function"* in chapter 7 of the "Operation manual

(for general information and copier operation)".)

* Can only be used on the AR-M351N/AR-M451N, or when the document filing function has been added.

 If the receiving party is busy

If the receiving party is busy, the transmission is temporarily cancelled and then automatically re-attempted after

a brief interval (two attempts are made at an interval of 3 minutes*). If you do not want the machine to re-attempt

the transmission, cancel the job in the job status screen. (See following page.)

*This setting can be changed with the key operator program (See "Recall in case of line busy" on page 8-8.).

 If a transmission error occurs

If an error occurs that prevents transmission or the receiving machine does not answer the call within 45

seconds*, then transmission is stopped and then automatically re-attempted later. (one recall attempt is made

at an interval of 3 minutes*) Automatic recalling can be stopped by pressing the [JOB STATUS] key and

cancelling as explained on the following page. This machine also supports error correction mode (ECM) and is

set to resend any part of a fax that is distorted due to noise on the line. (See "ECM" on page 8-7)

* The settings can be changed in the key operator programs. (See "Call timer at memory sending" and "Recall

in case of communication error" on page 8-8).

 Image rotation

The machine is initially set to rotate a vertically-placed ( )document 90° so that it is oriented horizontally( )

before transmission (A4 (8-1/2"x11") originals are rotated to A4R (8-1/2"x11"R) and B5R or A5R (5-1/2"x8-1/2"R)

originals are rotated to B5 or A5 (5-1/2"x8-1/2")). A4R (8-1/2"x11"R) originals and B5 or A5 (5-1/2"x8-1/2")

originals are not rotated. If desired, you can turn this function off with the key operator program as explained in

"Rotation sending setting." on page 8-7.

NOTES

 The machine is initially set (factory setting) to perform Quick On-line transmission. If desired, you can turn off this

function with the key operator program (See "Quick on line sending" on page 8-8).

 When a document is transmitted using the following methods, the job will be stored in memory (Quick On-line

transmission will not be performed):



Sending from the document glass



Broadcast transmission (page 3-2)



Timer transmission (page 3-6)



2 in 1 (page 3-7)



Card shot (page 3-8)



Job build (page 3-10)



F-code transmission (Chapter 4)

NOTES

 You can check transmission jobs stored in memory in the job status screen. (Refer to page 1-15 of "Operation

manual (for general information and copier operation)".)



If the memory becomes full while a document is being scanned, a message will appear in the display. You can

cancel the transmission by touching the [CANCEL] key, or send only the pages already scanned by touching the

[SEND] key. The page that was being scanned when the memory became full will be cleared from memory. If the

memory becomes full while scanning the first page of a document, the transmission job is automatically

cancelled.

 The number of jobs that can be stored will depend on the number of pages in each job and the transmission

conditions. The number of storable jobs will increase if the optional expansion memory (AR-MM9) is installed.

NOTE

Place A5 (5-1/2"x8-1/2") size originals so that they are oriented vertically ( ). If oriented horizontally ( A5R

(5-1/2"x8-1/2"R) orientation), the original size will be detected as A4 (8-1/2"x11") size on the document glass, or

A5R (5-1/2"x8-1/2"R) size in the automatic document feeder, and thus the original size must be set manually by

touching the [ORIGINAL] key and then the [A5R] ([5-1/2"x8-1/2"R]) key. (See "MANUALLY SETTING THE

SCANNING SIZE" on page 1-8.)

1 2 ... 23 24 25 26 27 28 29 30 31 32 33 ... 103 104

Kommentare zu diesen Handbüchern

Keine Kommentare

Flex 60 TPO Uživatelský manuál (2 strany)

Značka: Flex | Kategorie: For Home | Velikost: 0.07 MB |

Tabulka s obsahem

Product Data Sheet

Další produkty a příručky pro Pro domov Flex

Modely	Typ Dokumentu
TPO 60 Self Adhered	Uživatelský manuál Flex TPO 60 Self Adhered User Manual, 2 stránky
80 TPO	Uživatelský manuál Flex 80 TPO User Manual, 2 stránky
TPO PLUS Adhered roof membrane	Uživatelský manuál Flex TPO PLUS Adhered roof membrane User Manual, 5 stránky
7008 Laminating Adhesive	Uživatelský manuál Flex 7008 Laminating Adhesive User Manual, 2 stránky
Bonding Adhesive	Uživatelský manuál Flex Bonding Adhesive User Manual, 2 stránky
FB LOW Rise Adhesive	Uživatelský manuál Flex FB LOW Rise Adhesive User Manual, 2 stránky
LA432M	Uživatelský manuál Flex LA432M User Manual, 2 stránky
TPO Primer	Uživatelský manuál Flex TPO Primer User Manual, 2 stránky
HE903	Uživatelský manuál Flex HE903 User Manual [en] , 2 stránky
Pourable Sealert	Uživatelský manuál Flex Pourable Sealert User Manual [de] , 2 stránky
Substrate Adhesive 7003	Uživatelský manuál Flex Substrate Adhesive 7003 User Manual, 2 stránky
TPO Clear Cut-Edge Sealant	Uživatelský manuál Flex TPO Clear Cut-Edge Sealant User Manual, 2 stránky
TPO Bonding Adhesive	Uživatelský manuál Flex TPO Bonding Adhesive User Manual, 3 stránky
TPO Substrate Adhesive	Uživatelský manuál Flex TPO Substrate Adhesive User Manual, 2 stránky
TPO Low VOC Bonding Adhesive	Uživatelský manuál Flex TPO Low VOC Bonding Adhesive User Manual, 3 stránky
TPO WB Substrate Adhesive	Uživatelský manuál Flex TPO WB Substrate Adhesive User Manual, 2 stránky
TPO Weathered Membrane Cleaner	Uživatelský manuál Flex TPO Weathered Membrane Cleaner User Manual, 3 stránky
Thermoplastic Pourable Sealer	Uživatelský manuál Flex Thermoplastic Pourable Sealer User Manual, 2 stránky
80 Mil SS Base Sheet	Uživatelský manuál Flex 80 Mil SS Base Sheet User Manual, 2 stránky
140N Geotextile Separation Layer	Uživatelský manuál Flex 140N Geotextile Separation Layer User Manual, 1 stránky

Sharp AR-FX12 Spezifikationen Seite 28

Kommentare zu diesen Handbüchern

Flex 60 TPO manuály

Flex 60 TPO Uživatelský manuál (2 strany)

Tabulka s obsahem

Další produkty a příručky pro Pro domov Flex

Sharp AR-FX12 Spezifikationen Seite 28

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kopierer Sharp AR-FX12

Flex 60 TPO manuály

Flex 60 TPO Uživatelský manuál (2 strany)

Tabulka s obsahem

Další produkty a příručky pro Pro domov Flex