Sharp AL-1650 Spezifikationen

• GETTING STARTED• MAKING COPIES• STATUS INDICATORS• GENERAL INFORMATION2163242DIGITAL LASER COPIEROPERATION MANUALMODELAL-1650Page

8GETTING STARTED4" (10 cm)Copier installationCOPIER INSTALLATIONImproper installation may damage the copier. Please note the following duringinit

9GETTING STARTEDCAUTIONS ON HANDLINGBe careful in handling the copier as follows to maintain the performance of thiscopier.Do not drop the copier, sub

10GETTING STARTEDCHECKING PACKED COMPONENTSAND ACCESSORIESOpen the carton and check to ensure that the following components and accessoriesare include

11GETTING STARTEDSET-UP1Remove all pieces of tape, then open the documentfeeder cover and remove the protective material.2Use a coin (or other suitabl

12GETTING STARTEDSet-upSET-UPPressureplate lockScrew6Store the pressure plate lock which has been removedin step 5 and the screw which has been remove

13GETTING STARTED1Gently lift and pull out the paper tray until it stops.2Push the pressure plate down until it locks in place.3Fan the copy paper and

14GETTING STARTEDChanging the copy paper size in the tray1Gently lift and pull out the paper tray until it stops.2Push the pressure plate down until i

15GETTING STARTED8To set the selected paper size, press the PAPER SIZEENTER ( ) key.●The selected paper feed location indicator will blink and the cor

16MAKING COPIESNORMAL COPYINGThis copier has two document input stations — a singlepass feeder (SPF) for automatic document feeding and anoriginal tab

17MAKING COPIESNormal copyingNORMAL COPYINGUnits digitTens digit●For manual copy density adjustment, press the AUTO/MANUAL/PHOTO ( / / ) key to select

FOR YOUR PROTECTION...To aid in reporting this compact copier in case of loss or theft, please record below themodel number and serial number located

18MAKING COPIESUsing the original table1Turn the power switch on.●It will take about 35 seconds for the copier to warm up. However, youcan make desire

19MAKING COPIES●For photographs, select PHOTO ( ) and then adjust with the light( ) and dark ( ) keys as desired.●There are 5 exposure steps indicated

20MAKING COPIESREDUCTION/ENLARGEMENT/ZOOMReduction and enlargement ratios can be selected either automatically with theAUTO IMAGE ( ) key or manually

21MAKING COPIESManual1Place the original in the document feeder tray or on theoriginal table.2Use the PRESET RATIO selector ( , ) keys and thezoom (

22MAKING COPIES1Unfold the bypass tray.●When feeding 8-1/2" x 14" or 11" x 17" sized paper, extend the bypasstray.2Set the paper g

23MAKING COPIES4Press the TRAY SELECT ( ) key to select the bypasstray.5Leave the copy quantity at 0 if using special papers. Setthe number of copies

24MAKING COPIESTWO-SIDED COPYINGTwo-sided copies can be made on this copier using the bypass tray.Two-sided copying1Place the first original on the or

25MAKING COPIESXY ZOOMThe XY ZOOM feature allows the horizontal and vertical copy ratios to bechanged independently.To use the XY ZOOM feature with th

26MAKING COPIES XY zoomXY ZOOM5Use the PRESET RATIO selector ( , ) keys andzoom ( , ) keys to change the copy ratio in thehorizontal direction in a

27MAKING COPIES1Place the original in the document feeder tray or on theoriginal table.2Press the B/W REVERSE ( ) key.3Check the copy paper size.●If y

1GETTING STARTEDSTATUS INDICATORSMAKING COPIESGENERAL INFORMATIONCONTENTS PageGETTING STARTED●CAUTIONS . . . . . . . . . . . . . . . . . . . . . . . .

28MAKING COPIES1Place the originals on the original table with the center ofthe two pages aligned with the paper size index ( 81/2).Close the document

29MAKING COPIES1Press the INTERRUPT ( ) key.●The copier will return to the initial settings.●When the SPF is being used, the copier will stop after co

30MAKING COPIES1Press the AUTO/MANUAL/PHOTO ( / / ) keyto select the PHOTO ( ) mode.2Press and hold down the AUTO/MANUAL/PHOTO ( // ) key for approxim

31MAKING COPIESToner save modeTONER SAVE MODEThis mode reduces toner consumption by approximately 10% in the automaticand manual exposure modes. Copie

32STATUS INDICATORS1Open the bypass tray. Lift slightly on the side cover andslide the cover out until it stops.2Push gently the right side of the fro

33STATUS INDICATORS TD cartridge replacementTD CARTRIDGE REPLACEMENT5Remove the protective cover from the TD cartridge byunlatching three cover hooks

34STATUS INDICATORS1Open the bypass tray. Lift slightly on the side cover andslide the cover out until it stops.2Push gently the right side of the fro

35STATUS INDICATORSDRUM CARTRIDGE REPLACEMENT Drum cartridge replacement5Remove the new drum cartridge from the protective bagand gently insert the le

36STATUS INDICATORSMISFEED REMOVALThe copier will stop when a misfeed occurs. The misfeed ( ) indicator will blinkand blinking red misfeed location in

37STATUS INDICATORS Misfeed removalMISFEED REMOVAL3If the misfed original cannot be removed in steps 1 and2, remove the misfed original from the exit

2GETTING STARTEDCautionsCAUTIONSFollow the cautions below when using this copier.●The fusing area is hot. Exercise care in this area when removing mis

38STATUS INDICATORSMISFEED REMOVAL Misfeed removalIf the misfed paper is seen from this side, proceed to “C. Misfeed in the transport area”.If paper i

39STATUS INDICATORSMISFEED REMOVAL Misfeed removalRoller rotating knobFusing unit release lever2Turn the roller rotating knob in the direction of thea

40STATUS INDICATORSMISFEED REMOVAL Misfeed removal3Close the side cover by pressing the handle on the cover.●The misfeed ( ) indicator will go out.Mis

41STATUS INDICATORS2Remove the misfed paper.●Be careful not to tear the misfed paper during removal.3If the misfed paper is not seen in step 2, gently

42GENERAL INFORMATIONUser programsUSER PROGRAMSThe user programs allow the parameters of certain functions to be set, changed, orcanceled as desired.L

43GENERAL INFORMATION3Press the START ( ) key.●The entered program number will be steadily lit on the left side of thecopy quantity display and the cu

44GENERAL INFORMATIONPOWER SAVE MODESThe copier has two power save modes to reduce overall power consumptionthereby reducing the cost of operation. In

45GENERAL INFORMATIONSetting the power save modesThe time that elapses before the copier enters a power save mode after anyoperation is made can be se

46GENERAL INFORMATIONUser maintenanceUSER MAINTENANCEProper care is essential for clean, sharp copies. Please take a few minutes toregularly clean you

47GENERAL INFORMATIONCharger cleanerUSER MAINTENANCEUser maintenance1Turn the power switch off.2Open the bypass tray. Lift slightly on the side cover

3GETTING STARTEDMAIN FEATURES➀High-speed laser copying●First-copy time is only 7.2 seconds (except in a power save mode or immediately after power on)

48GENERAL INFORMATIONProblem Solution●Copier plugged in?●Power switch ON?●Copy density properly adjusted?●Is the original placed face down onthe ori

49GENERAL INFORMATIONThe TD cartridge is not installed. Install theTD cartridge.Side cover is open.Close the front and side covers securely.The TD car

50GENERAL INFORMATIONSUPPLIESTypes and sizes of copy paperSize Weight Capacity Special paper(21 lb. bond paper)Paper tray 5-1/2" x 8-1/2"* 1

51GENERAL INFORMATIONSUPPLIESGenuine supplies statementStandard supplies for this copier that are to be replaced by the user are copypaper, TD cartrid

52GENERAL INFORMATIONMOVING INSTRUCTIONSWhen moving this copier, follow the procedure below.When moving this copier, be sure to remove the TD cartridg

53GENERAL INFORMATIONType Digital copying machine, desktopCopy system Dry, electrostatic transferOriginals Sheets, bound documentsOriginal sizes Max.

54GENERAL INFORMATIONSPECIFICATIONSSpecificationsOverall dimensions 23-15/64" (W) x 20-23/32" (D)(with bypass tray folded) (590 mm (W) x 526

55GENERAL INFORMATIONAAuto clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Automatic exposure adjustment . . . . . . .

56GENERAL INFORMATIONSScrew . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11, 52Single pass feeder (SPF). . . . . . . . . . .

57SHARP Date Issued:Nov. 1, 1998MATERIAL SAFETY DATA SHEETMSDS No. F-00841Section 1. Product IdentificationProduct:AL-160TD (Black Toner)Section 2. Su

4GETTING STARTEDPART NAMES AND FUNCTIONSOverall layoutPart names and functionsq Document feeder coverOpen to make copies from the original table.w Ori

58Section 6. Physical Chemical CharacteristicsBoiling / Melting Point: Not applicable Specific Gravity: 1.1Vapor Pressure: Not applicable Solubility i

59SHARPDate Issued :Nov. 1, 1998MATERIAL SAFETY DATA SHEETMSDS No. F-30841Section 1. Product IdentificationProductAL-160TD(Black Developer)Section 2.

60Section 6. Physical Chemical CharacteristicsBoiling / Melting Point: Not applicable Specific Gravity: about 7.3Vapor Pressure: Not applicable Solubi

61MEMO

MEMO

WARNING:FCC Regulations state that any unauthorized changes or modifications tothis equipment not expressly approved by the manufacturer could void th

PRINTED IN HONG KONG99D KS TINSE0230QSZZAL-1650SHARP ELECTRONICS CORPORATIONSharp Plaza, Mahwah, New Jersey 07430-2135.SHARP CORPORATIONwww.sharp-u

5GETTING STARTEDPART NAMES AND FUNCTIONS!5 SPF exit areaFinished originals are output here.!6 Document feeder trayHolds up to 30 originals.!7 Original

6GETTING STARTEDOperationpanelPART NAMES AND FUNCTIONSPart names and functionsq Operation panel and keys for printer functionsSee the printer manual.w

7GETTING STARTEDPART NAMES AND FUNCTIONSPart names and functionsGETTING STARTEDti !0 !1 !3!2@6@5@4@3@2@1!6 DUAL PAGE COPY ( ) key and indicator(p. 28)