Sharp R-380E Betriebsanleitung

1 Ver.: 2.2 Tajfun Planina, proizvodnja strojev d.o.o. Planina 41 a, 3225 Planina pri Sevnici, Slovenija Tel.: +386 (0)3 746 44 20, Fax.: +386 (0)3 57

10 3.3 STARTING UP: Before each machine startup, it is necessary to check the chain tension and readjust it if necessary! A too loose chain can induc

11 The maximum allowable speed of the tractor when transporting the machine on the rut or off-road is 10 km/h (12 mph) and 40 km/h (25 mph), when the

12 7 H P 6 A 11 12 10

13 4.3 SAWING The barsaw is always operating. The sawbar movement is performed using the sawbar activation handle (H-Figure: 7), during which the saw

14 4.4.1 ADJUSTING THE HEIGHT OF THE SPLITTING WEDGE By using a splitting wedge handle (L-Figure: 10), the splitting wedge can be gradually lifted or

15 4.5 DISCHARGE CONVEYOR Lifting and lowering of the discharge conveyor is performed with the hand winch handle (23-Figure: 12). When the desired pos

16 5 MAINTENANCE AND REPAIR Regular machine maintenance ensures reliable operation and long lifetime of the machine 5.1 CUTTING CHAIN REPLACEMENT B

17 5.2 CUTTING CHAIN TENSIONING • Loosen both nuts (34-Figure: 15) on the fixing plate (35-Figure: 15) • Tighten the tensioning screw (33-Figure: 15)

18 Hydraulic oil – suitable brands: (Viscosity: 46 mm2/s at 40oC) Manufacturer’s: Substitute oils: Castrol Hyspin AVH 46 Mobil DTE 16 Renolin B 4

19 5.8 TROUBLESHOOTING PROBLEM POSSIBLE CAUSES SOLUTION The machine does not react to movements of the sawbar activation handle Check the machin

2 TABLE OF CONTENTS Page: 1 GENERAL 3 1.1 MANUFACTURER’S ADDRESS 3 1.2 APPLICATION 4 1.3 SCOPE OF DELIVERY 4 1.4 OPTIONAL EQUIPMENT 4 1.5

20 ⊗ More demanding procedures must be performed by a qualified technical service only. (**) In worse operating conditions with high temperatures of

21 19 a b c d WHAT? WHEN? HOW? Lubrication (Figure:19) Lubrication Point: a, b, c At least every 80 hours of operation Lithium Grease Lubricati

22 5.10 CUTTING CHAIN BELT REPLACEMENT • Disconnect the machine from the drive or unplug the power cord from the electrical outlet • Remove the drive

23 5.10.1 BELT TENSIONING The machine must be stopped, during the operation! Set the correct tension of the belt using the notch on the tension indic

24 5.11 INDICATIONS OF IMPROPER USE • Torn or damaged in-feed or discharge conveyor belts • Torn cutting chain • Damaged chain guide (sawbar) • Dama

25 Tajfun Planina, proizvodnja strojev d.o.o. Planina 41 a, 3225 Planina pri Sevnici, Slovenija Tel.: +386 (0)3 746 44 20, Fax.: +386 (0)3 5791 016 E-

26 Tajfun Planina, proizvodnja strojev d.o.o. Planina 41 a, 3225 Planina pri Sevnici, Slovenija Tel.: +386 (0)3 746 44 20, Fax.: +386 (0)3 5791 016 E-

27

28 WARRANTY SHEET We guaranty: • that the product will operate fault free, if operated according to enclosed operating instructions; • that we will

3 Dear Customer, By purchasing our firewood processor you obtained the equipment which will provide you with great help in your work. To make operati

4 1.2 APPLICATION Firewood processor (RCA 380, RCA 380 E) is a machine used for preparation of firewood. The processor can handle logs from 10 to 38

5 EP 11 ELECTRIC POWER UNIT EP 11 – Tajfun Motor Power: 11 kW Weight: 197 kg

6 1.5 TECHNICAL DATA Length of Cut Log 25 – 50 cm (10" - 20") Diameter of Log 10 – 38 cm (4 – 15") Sawbar Oregon 17", b=0,058&

7 2 SAFETY INSTRUCTIONS • Machine operation and maintenance is allowed to qualified persons older then 18 years of age, only! • Before starting the w

8 Change the rotating direction of the electric motor by inverting the poles on the plug. RCA 380 E : Connect the RCA 380 E to the thee-p

9 3.1.1 RETRACTION OF THE DISCHARGE CONVEYOR Discharge conveyor is usually telescopically retracted in the machine transport position. By activating