Sharp AL-1200 Spezifikationen

FOR YOUR PROTECTION...To aid in reporting this compact copier in case of loss or theft, please record below themodel number and serial number located

92InstallationBe sure to allow the required space aroundthe machine for servicing and properventilation.A small amount of ozone is produced within the

102InstallationCHECKING PACKED COMPONENTS ANDACCESSORIESOpen the carton and check if the following components and accessories are included.CopierPower

112InstallationREMOVING PROTECTIVE PACKING MATERIALS1Remove pieces of tape , , , , and and protective cover . Then openthe original cover and r

122InstallationINSTALLING THE TD CARTRIDGE2Remove the CAUTION tape from the front cover and remove the two protective pinsfrom the fusing unit by pull

132InstallationINSTALLING THE TD CARTRIDGE6Gently insert the TD cartridge until it locks in place.7Close the front cover and then the side cover by pr

142InstallationLOADING COPY PAPER2Remove the pressure plate lock. Rotate the pressure plate lock in the direction of thearrow to remove it while press

152InstallationLOADING COPY PAPER6Gently push the paper tray back into the copier.After loading copy paper, to cancel the blinking “P” without restart

162InstallationPOWER ONTurn the power switch on the left side of the copier to the “ON” position. The ready ( )indicator will light up and other indic

173Making copies3MAKING COPIESThis chapter describes basic copying functions and some other copying functions using thebypass tray.PAPERFor best resul

183Making copiesNORMAL COPYING1Ensure that paper of the desired size is set in the paper tray. See page 13, LOADINGCOPY PAPER. When copying onto 8-1/2

1CONTENTS1 GETTING STARTEDINTRODUCTION 3CAUTIONS 3MAIN FEATURES 4PART NAMES 6OPERATION PANEL 72 INSTALLATIONCOPIER INSTALLATION

193Making copiesNORMAL COPYING6Set the number of copies using the two copy quantity ( , ) keys.●Press the clear ( ) key to clear an entry if a mistak

203Making copiesEXPOSURE ADJUSTMENT/PHOTO COPYINGCopy density adjustment is not required for most originals in the automatic exposure mode. Toadjust t

213Making copiesREDUCTION/ENLARGEMENT/ZOOMTo select a preset copy ratio: To select a zoom ratio:Preset reduction and enlargement ratiosare: 50%, 64%,

223Making copiesBYPASS FEEDTo close the bypass tray, performstep1 and then step 2 in theillustration and push the roundprojections at the right of the

233Making copiesTWO-SIDED COPYING1Place the first original on the original table and make a copy.The first copy can be made using either the paper tra

244Special functionsSPECIAL FUNCTIONSDESCRIPTION OF SPECIAL FUNCTIONSThis chapter describes the special functions of this copier. Use these functions

254Special functionsTONER SAVE MODE2Press and hold down the exposure mode selector key for approximately 5 seconds.The manual ( ) indicator will go ou

264Special functionsUSER PROGRAMS3Press the print ( ) key. The entered program number will be steadily lit and thecurrently selected parameter number

275Supplies and user maintenance5SUPPLIES AND USER MAINTENANCEThis chapter describes how to replace the TD cartridge and the drum cartridge and how to

285Supplies and user maintenanceTD CARTRIDGE REPLACEMENT3Install a new TD cartridge. To install the new cartridge, see page 11, INSTALLINGTHE TD CARTR

25SUPPLIES AND USER MAINTENANCE TD CARTRIDGE REPLACEMENT 27DRUM CARTRIDGE REPLACEMENT 28USER MAINTENANCE 29– Cabinet 29– Original tab

295Supplies and user maintenanceDRUM CARTRIDGE REPLACEMENT4Remove the new drum cartridge from the protective bag and remove the protectivecover from t

305Supplies and user maintenanceTransfer chargerIf copies start becoming streaky or blotchy, the transfer charger may be dirty. Clean the chargerusing

315Supplies and user maintenanceUSER MAINTENANCECopier lens cleaningIf white lines appear on copies from top edge to bottom edge, do the following tes

326Copier trouble?6COPIER TROUBLE?This chapter describes misfeed removal and troubleshooting.MISFEED REMOVALWhen the misfeed ( ) indicator blinks or

336Copier trouble?MISFEED REMOVAL2Close the side cover by pressing the round projections near the side cover openbutton. The misfeed ( ) indicator wil

346Copier trouble?MISFEED REMOVAL3Raise the fusing unit release lever and then close the side cover by pressing theround projections near the side cov

356Copier trouble?TROUBLESHOOTINGIf any problem occurs, check the list below before contacting the Sharp Service Center.See page:1516––1824243720

366Copier trouble?STATUS INDICATORSWhen the following indicators light up or blink on the operation panel or the followingalphanumeric codes appear in

376Copier trouble?AUTOMATIC EXPOSURE ADJUSTMENTThe automatic exposure level can be adjusted to suit your copying needs.1Press the exposure mode select

387Appendix7APPENDIXSPECIFICATIONSType Digital copying machine, desk-top typeCopy system Dry, electrostatic transferOriginals Sheets, bound documentsO

31Getting startedThis chapter provides basic information for using the copier.INTRODUCTIONThis copier has been designed to provide intuitive operating

397AppendixOPTION AND SUPPLY PART NUMBERS AND STORAGEWhen ordering supplies and option, please use the correct part numbers as listed below.Be sure to

407AppendixMOVING INSTRUCTIONSWhen moving this copier, follow the procedure below.When moving this copier, be sure to remove the TD cartridge in advan

INDEXAAuto clear . . . . . . . . . . . . . . . . . . . . . 24, 25Automatic exposure adjustment . . . . . . . 37Auto power shut-off mode . . . . . . .

Power cord . . . . . . . . . . . . . . . . . . . . 10, 15Power on . . . . . . . . . . . . . . . . . . . . . . . . . 16Power save modes . . . . . . . .

MEMO

MEMO

WARNING:FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void

SHARP ELECTRONICS CORPORATIONSharp Plaza, Mahwah, New Jersey 07430-2135.WWW.SHARP-USA.COMSHARP CORPORATION© 1998 SHARP CORPORATIONPRINTED IN JAPANTINS

41Getting startedSAFETY PRECAUTIONSThis Digital Copier is rated Class 1 and complies with 21 CFR 1040.10 and 1040.11 ofthe CDRH standards. This means

51Getting startedMAIN FEATURESr Scan once/ Print many (AL-1041 only)●The AL-1041 is equipped with a 1-page memory buffer. This Memory allows theAL-104

61Getting startedPART NAMESTransfer chargerTD cartridge lock release buttonTD cartridgeDrum cartridgeDrum cartridge handlePaper feed rollerFusing unit

71Getting startedOPERATION PANELq Exposure mode selector key andindicatorsUse to sequentially select the exposuremodes: AUTO, MANUAL or PHOTO.Selected

82Installation2INSTALLATIONFollow the installation procedure below to use the copier properly.COPIER INSTALLATIONImproper installation may damage the