Sharp XV-Z100 Spezifikationen PDF herunterladen (Seite 52)

WARNING:

The coolig fa i this pr ojector cotiues to ru for about 90 secods after the projector eters

stadby mode. Durig ormal operatio, whe puttig the projector ito stadby mode always

use the S T ANDBY/ON butto o the projector or the STANDBY butto o the remote cotrol.

Esure the coolig fa has stopped befor e discoectig the power cor d.

DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING

THE POWER CORD. FAILURE TO OBSERVE THIS WILL RESUL T IN PREMA TURE LAMP FAILURE.

Caution Concerning Lamp Replacement

See Replacig the Lamp o page 50.

PRODUCT DISPOSAL

This pr ojector utilizes ti-lead solder, ad a pressurized lamp cotaiig a small amout of

mercury . Disposal of these materials may be r egulated due to evirometal cosideratios.

For disposal or recyclig iformatio, please cotact your local authorities or, if you are

located i the Uited States of America, the Electroic Idustries Alliace: www.eiae.org .

This SHARP projector uses a DMD pael. This very sophisticated pael cotais 09,920 pixels

(micromirrors). As with ay high techology electroic equipmet such as large scree TVs,

video systems ad video cameras, there ar e certai acceptable toleraces that the equipmet

must coform to.

This uit has some iactive pixels withi acceptable toleraces which may result i iactive dots

o the picture scr ee. This will ot af fect the pictur e quality or the life expectacy of the uit.

XV-Z100_EN_b 05.8.25, 5:50 AM2

Downloaded From projector-manual.com Sharp Manuals

Maintenance Indicators

About the lamp indicator

 When the remaining lamp life becomes 5% or less, (yellow) and “Change The Lamp” will be

displayed on the screen. When the percentage becomes 0%, it will change to (red), the lamp will

automatically turn off and then the projector will automatically enter standby mode. At this time, the

lamp indicator will illuminate in red.

 If you try to turn on the projector a fourth time without replacing the lamp, the projector will

not turn on.

About the temperature warning indicator

If the temperature inside the projector increases, due to blockage of the air vents, or the setting location,

“ ” will illuminate in the lower left corner of the picture. If the temperature keeps on rising, the lamp

will turn off and the temperature warning indicator will blink, the cooling fan will run, and then the projec-

tor will enter standby mode. After “ ” appears, be sure to perform the measures described on page

49.

Lamp indicator

 The warning lights (power indicator, lamp indicator and temperature warning indicator) on the

projector indicate problems inside the projector.

 If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate

red, and the projector will enter standby mode. After the projector has entered standby mode,

follow the procedures given below.

Temperature warning indicator

Power indicator

Lamp indicator

Red on

Power indicator

Indicators on the Projector

Green on

Normal (Standby)

Normal (Power on)

Green on

Green blinks

Normal

The lamp is warming up or shutting down.

Temperature warning

indicator

Off

Red on

Normal

The internal temperature is abnormally

high. (See page 49.)

Red blinks Abnormal (See page 49.)

Red on The lamp is shut down abnormally or

requires to be changed. (See page 49.)

Green blinks

Normal (Cooling)

Top View

XV-Z100_EN_l 05.8.25, 5:58 AM48

Downloaded From projector-manual.com Sharp Manuals

1 2 ... 47 48 49 50 51 52 53 54 55 56 57 ... 64 65

Kommentare zu diesen Handbüchern

Keine Kommentare

Sharp XV-Z100 Spezifikationen Seite 52

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Datenprojektoren Sharp XV-Z100