Sharp AL-1551 Bedienungsanleitung

Digital Laser Copier/PrinterOperation Manual MODELAL-1551

82Installation2INSTALLATIONFollow the installation procedure below to use the copier properly.COPIER INSTALLATIONImproper installation may damage the

92InstallationBe sure to allow the required space aroundthe machine for servicing and properventilation.A small amount of ozone is produced within the

102InstallationCHECKING PACKED COMPONENTS ANDACCESSORIESOpen the carton and check if the following components and accessories are included.CopierPower

112InstallationREMOVING PROTECTIVE PACKING MATERIALS1Remove all pieces of tape shown in the illustration below. Then open the originalcover and remove

122InstallationINSTALLING THE TD CARTRIDGE1Open the bypass tray and then open the side cover while pressing the side coveropen button.Bypass tray2Remo

132InstallationINSTALLING THE TD CARTRIDGE5Gently insert the TD cartridge until it locks in place.6Close the front cover and then the side cover by p

142InstallationLOADING COPY PAPER2Remove the pressure plate lock. Rotate the pressure plate lock in the direction of thearrow to remove it while press

152InstallationLOADING COPY PAPER6Gently push the paper tray back into the copier.After loading copy paper, to cancel the blinking “P” without restart

162InstallationPOWER ONTurn the power switch on the left side of the copier to the “ON” position. The ready ( )indicator will light up and other indic

173Making copies3MAKING COPIESThis chapter describes basic copying functions and some other copying functions using thebypass tray.PAPERFor best resul

FOR YOUR PROTECTION...To aid in reporting this compact copier in case of loss or theft, please record below the modelnumber and serial number located

183Making copiesNORMAL COPYINGThis copier has two document input stations - a reversing single pass feeder (RSPF) for automaticdocument feeding and an

193Making copiesNORMAL COPYINGA. When using the RSPF:(1) Make sure that no original is left on the original table.(2) Adjust the original guides to th

203Making copiesNORMAL COPYINGWhen copying a book or an original which has been folded or a crumpledoriginal, press down the original cover lightly. I

213Making copiesZOOMTens digit Unit digitNORMAL COPYING5Ensure that the desired paper tray is selected.●Paper sizes that can be used in the duplex cop

223Making copiesNORMAL COPYING8When making two-sided copies from the original table, place the second original onthe original table and press the prin

233Making copiesEXPOSURE ADJUSTMENT/PHOTO COPYING3Use the light ( ) and dark ( ) keys to adjust the exposure level.If exposure level 2 is selected, th

243Making copiesREDUCTION/ENLARGEMENT/ZOOMTo decrease or increase the zoom ratio rapidly, press and hold down the or key. However the value will sto

253Making copiesBYPASS FEEDTo close the bypass tray, performstep1 and then step 2 in theillustration and push the roundprojections at the right of the

264Special functionsSPECIAL FUNCTIONSDESCRIPTION OF SPECIAL FUNCTIONSThis chapter describes the special functions of this copier. Use these functions

274Special functionsTONER SAVE MODE2Press and hold down the exposure mode selector key for approximately 5 seconds.The manual ( ) indicator will go ou

1CONTENTS1 GETTING STARTEDINTRODUCTION 3CAUTIONS 3MAIN FEATURES 4PART NAMES 6OPERATION PANEL 72 INSTALLATIONCOPIER INSTALLATION

284Special functionsUSER PROGRAMS3Press the print ( ) key. The entered program number will be steadily lit and thecurrently selected parameter number

295Supplies and user maintenance5SUPPLIES AND USER MAINTENANCEThis chapter describes how to replace the TD cartridge and the drum cartridge.Be sure to

305Supplies and user maintenanceTD CARTRIDGE REPLACEMENT3Install a new TD cartridge. To install the new cartridge, see page 12, INSTALLINGTHE TD CART

315Supplies and user maintenanceDRUM CARTRIDGE REPLACEMENT4Remove the new drum cartridge from the protective bag and remove the protectivecover from t

325Supplies and user maintenanceUSER MAINTENANCEProper care is essential in order to get clean, sharp copies. Be sure to take a few minutes toregularl

335Supplies and user maintenanceUSER MAINTENANCETransfer chargerIf copies start becoming streaky or blotchy, the transfer charger may be dirty. Clean

345Supplies and user maintenanceWhen copier is not in useTo prevent entry of dust and foreign matter, store the copier as follows.1Remove the power co

356Copier trouble?6COPIER TROUBLE?This chapter describes misfeed removal and troubleshooting.MISFEED REMOVALWhen the misfeed ( ) indicator blinks or

366Copier trouble?MISFEED REMOVALA Misfeed in the paper feed area1Gently remove the misfed paper from the paper feed area as shown in the illustratio

376Copier trouble?MISFEED REMOVAL●Do not touch the surface of the drum (green portion) of the drum cartridgewhen removing the misfed paper. Doing so m

25SUPPLIES AND USER MAINTENANCE TD CARTRIDGE REPLACEMENT 29DRUM CARTRIDGE REPLACEMENT 30USER MAINTENANCE 32– Cabinet 32– Original tab

386Copier trouble?3Rotate the feeding roller in the direction of the arrow and gently remove the misfedpaper from the exit area.Feeding roller4Raise t

396Copier trouble?MISFEED REMOVALE Misfeed in the RSPFAn original misfeed may occur at one of three locations: if the misfed original is seen from th

406Copier trouble?MISFEED REMOVAL(C) If the original does not move easily into the exit area, remove it in the direction of thearrow while rotating th

416Copier trouble?TROUBLESHOOTINGIf any problem occurs, check the list below before contacting our Technical AssistanceDepartment.See page:1516––18262

426Copier trouble?STATUS INDICATORSWhen the following indicators light up or blink on the operation panel or the following alphanumericcodes appear in

436Copier trouble?AUTOMATIC EXPOSURE ADJUSTMENTThe automatic exposure level can be adjusted to suit your copying needs. This level is set forcopying f

447Appendix7APPENDIXSPECIFICATIONSType Digital laser copier/printer, desk-top typeCopy system Dry, electrostatic transferOriginals Sheets, bound docum

457AppendixMemory 6 MBPower supply AC 120V (±10%), 60 Hz (±2%)Power consumption 1,000 WOverall dimensions 31.9" (W) x 18.8" (D) (809 mm (W)

467AppendixSUPPLY PART NUMBERS AND STORAGEWhen ordering supplies, please use the correct part numbers as listed below.Be sure to use only genuine SHAR

477AppendixMOVING INSTRUCTIONSWhen moving this copier, follow the procedure below.When moving this copier, be sure to remove the TD cartridge in advan

31Getting started1GETTING STARTEDThis chapter provides basic information for using the copier.INTRODUCTIONThis copier has been designed to provide int

INDEXAAuto clear . . . . . . . . . . . . . . . . . . . . 26, 27Automatic exposure adjustment . . . . . . 43Auto power shut-off mode . . . . . . . .

PPacked components . . . . . . . . . . . . . . . 10Paper– loading . . . . . . . . . . . . . . . . . . . . . . . . 13– special . . . . . . . . . . .

For users in the USAThis device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not

PRINTED IN CHINA2001J KS TINSE0679QSZZSHARP ELECTRONICS CORPORATIONSharp Plaza, Mahwah, New Jersey 07430-2135.www.sharp-usa.comSHARP ELECTRONICS OF

41Getting startedCAUTIONS●Place the copier on a firm, level surface.●Do not install the copier in a humid or dusty location.●When the copier is not us

51Getting startedMAIN FEATURESSubstantial copying functions●Zoom copying from 50% to 200% in 1% increments can be performed.●Continuous copying of max

61Getting startedPART NAMESRSPF exit area Original guidesFeeding roller coverDocumentfeeder trayTransfer chargerTD cartridge lock release buttonTD car

71Getting startedOPERATION PANELOriginal to copy key and indicators: Two-sided copies from one-sided originals.Turn on Long Edge or Turn onShort Edge