Sharp XG-P20XU Spezifikationen PDF herunterladen

Quick Start Reference Sheet

Sharp XG-P20XU

Revision B

DR-SHP17 – 9/04/02 SP Controls reserves the right to modify specifications without notice at any time.

NOTE: This document is intended only as a quick reference for installation – please read the following

SP Controls Application Note for a complete description of this projector driver prior to installation.

I. Driver Features

1. Input Selection Mapping

Selection 1: INPUT 1 (VGA)

Selection 2: INPUT 2 (5 BNC)

Selection 3: INPUT 4 (RCA)

Selection 4: INPUT 5 (S-Video)

2. Hidden Function Mapping

Selection 1: BLACK SCREEN

Selection 2: ENTER

Selection 3: ADJUST LEFT

Selection 4: ADJUST RIGHT

Off: MENU

Volume Up: ADJUST UP

Volume Down: ADJUST DOWN

3. Other Driver Features

Power Status Feedback Method Current Sensor

Control Wiring Option Wired Remote or IR Emitter

NOTE: Due to an interoperability issue, Power Polling for this projector is not available. If power feedback

is required, we recommend using a third party power current sensor. If the projector's automatic shutoff

timers are disabled, the SmartPanel will reliably remain in sync with the projector unless the projector is

powered on or off manually.

II. Wiring Specifications

NOTE: For a wiring diagram, please see the SP Controls Application Note for the Sharp XG-P20XU

1. RS-232:

Wire the Panel RS-232 port to a female DB9 as follows:

RX to 2

TX to 3

GND to 5

JUMPER 7 and 8

Connect this female DB9 to the projector port labeled RS-232C.

2. Infrared Emitter:

Wire the Panel IR/Serial port to a female 1/8" Mini as follows:

IR/SER to tip

GND to ring

Attach to the projector port labeled Wired Remote using a male 1/8” mini to male 1/8” mini (not

included).

III. Additional Projector Information

1. If the Panel is wired to the Projector’s Wired Remote port, the Wired Remote port must be manually

switched to IR on the projector.

2. You must set the Economy Mode labeled “MNTR Out/RS232C” to OFF. If you leave this setting on,

the Sharp will not respond to RS-232 control when in standby mode. See Application Note Section V.

Special Control Note for instructions.

1 2 3 4 5 6 7 8

Inhaltsverzeichnis

Seite 1

Quick Start Reference SheetSharp XG-P20XURevision BDR-SHP17 – 9/04/02 SP Controls reserves the right to modify specifications without notice at any ti

Seite 2 - Sharp XG-P20XU

Seite 3 - I. PROJECTOR CONTROL

Projector Driver Application NoteSharp XG-P20XURevision BDR-SHP17 – 9/04/02 SP Controls reserves the right to modify specifications without notice at

Seite 4

Seite 5

Seite 6 - II. CONTROL WIRING

Seite 7 - IV. TECHNICAL NOTES

Seite 8 - VI. REVISION HISTORY

Weitere Dokumente für Projektoren Sharp XG-P20XU

Um das Dokument anzuzeigen Sharp XG-P20XU Bedienungsanleitung

Sharp XG-P20XU Bedienungsanleitung (83 Seiten)

Kommentare zu diesen Handbüchern

Keine Kommentare

Sharp XG-P20XU Spezifikationen

Stöbern Sie online oder laden Sie Spezifikationen nach Projektoren Sharp XG-P20XU herunter. Sharp XG-P20XU Specifications Benutzerhandbuch

Inhaltsverzeichnis

Weitere Dokumente für Projektoren Sharp XG-P20XU

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Projektoren Sharp XG-P20XU