Sharp ER-01PU Spezifikationen Seite 27
- Seite / 86
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
ER-OIPU
If no status is selected, automatic status transmission is disabled.
If at least one status is selected, automatic status transmission is
enabled and 4-byte data is transmitted each time the selected status
changes.
The data to be transmitted are listed on the next page.
[Notes]
The status is transmitted without checking the DSR signal.
4 bytes are sent continuously when transmitting the status except for
I No. I COMMAND/
FUNCTION
I
CODE
I
58
1) GS V m
2) GS V m n
Cut paper
I
<1Dh><56h>
[Range]
XOFF.
[Function]
Executes a cut of the paper as specified by “m”.
[Reference]
DLE EOT:
Transmit status in real time
ESC
U: Transmit peripheral device status
ESC
V:
Transmit paper detector status
Ist byte (printer information)
1) m = O,m = 48: Full cut
m = 1, m = 49: Partial cut
2) m = 65:
Paper feed for (cut
full cut
m = 66 :
Paper feed for (cut
partial cut
[Notes]
calculation pitch)]) and
calculation pitch)]) and
position+[nx(basic
position+[nx(basic
bit
Function
Value 0/1
o Not used
Fixed to 0
1 Not used
Fixed to 1
2 Drawer status “L”/”H”
“L”/”H”
3 Online/Offline state
Online/Offline
4 Not used
Fixed to 1
5 HEAD UP LEVER
Close/Open
6 Paper feed SW
Paper not being fed/Paper being
fed
7 Not used
Fixed to O
1)is the same as ESC i / ESC m.
In case of 2), the paper is cut after being fed to the cut position when
“n” is O, and is cut after being fed to the position of (cut posi-
tion+[nx(basic calculation pitch)]) when “n” is not O.
Causion:
After this command is executed,
You had better execute one line
feed or one line print to prevent
the Paper Jam.
2nd byte (error information)
bit I
Function
Value 0/1
I
O ~Not defined
1 I Not defined
2 RS232 receive error
No error caused/Error
caused
3 Auto cutter error
No error caused/Error
caused
4 Not used Fixed to 1
5 Unrecoverable printer error
No error caused/Error
[Reference]
ESC i:
Full cut
ESC m: Partial cut
caused
6 Head temperature rise
No error caused/Error
caused
7 Not
used Fixed to O
I
59
I
GS a n
Enable/disable automatic
status transmission
I
<1Dh>c61h> n
I
[Range]
O~ n ~ 255
[Function]
Selects which status is to be covered by
sion.
3rd byte (paper detector information)
] bit I
Function
I
Value 0/1
I
o Near end detector
Paper is presentiPaper is out
I 1 I Notdefined
I
automatic status
transmis-
I 2 I Journal end detector
I PaDeris present/Paper is out
I
3 I Receipt end detector
I Paper is present/Paper is out
The meaning of each bit of “n” is as follows.
,
I Fixed to O
bit
Status to be covered by automatic status transmission
o
Drawer status 1: Enabled O:Disabled
1 Online/Offline
1: Enabled O:Disabled
! 5
!Not defined
I
I 6 I Not defined
I
I 7 I Not used
I Fixed to O
2 I Error state 1: Enabled O:Disabled
4th byte: dummy
3
Paper detector
1: Enabled O:Disabled
4
Not defined
5 I Not defined
6
Not defined
7 Not defined
4-18
- SERVICEMANUAL 1
- CHAPTER 1. SPECIFICATIONS 2
- ❑ 0 ‘ ❑ on ❑ c 3
- I I I UNIT: mm 4
- Printer interface 5
- I Interface 5
- IPL interface 6
- 9. Dip switch 6
- 10. Drawer inteflace 7
- 11. Buzzer / Memory/ Backup 7
- CHAPTER 2. OPTIONS 8
- CHAPTER 3. INITIAL PROCESSING 9
- 4. COMMAND DESCRIPTION 10
- Command description 11
- I I I I I 15
- YOUR RECEIPT 18
- THANK YOU 18
- I No. I COMMAND/ 27
- ●2: Start code,Stop code 28
- Characters 31
- Fixed to o 33
- @ International character set 44
- CHAPTER 6. HEXADECIMAL DUMP 45
- CHAPTER. 7 :ERROR HANDRING 45
- CHAPTER 8. DISASSEMBLY& 46
- ASSEMBLY 46
- 3. REMOVE THE CONTROL PWB AND 47
- PANEL PWB 47
- REMOVE THE PRINTER UNIT 47
- REMOVE THE N/F PS PWB UNIT 48
- CHAPTER 9. INSTALLATION OF 49
- SERVICE OPTIONS 49
- [PARTS LIST’J 50
- [DISASSEMBLY METHOD] 50
- CHAPTER 10. DIAGNOSTICS 51
- FUNCTION 51
- 3. Program code list 52
- Test items 53
- 4-5. RS232 loop test 54
- 47. RAM test 54
- 4-8. Auto test 55
- 4-11. A/D conversion test 56
- 4-12. DIP SW & J1/J2 test 56
- Loading) MODE 57
- Description of main LSI’S 60
- 2) Blockdiagram 61
- Pin description 62
- 3. Memory map 63
- 4. Printer control 63
- Auto cutter control 64
- 3) Paper end sensor circuit 64
- ! Al— 1171-1255 65
- ISolder J2 alone 65
- 5) Head up sensor circuit 66
- IRPFA.Rece@t paper 67
- <>-m 68
- )))) .) I I I I I I 70
- 1. Control PWB 73
- L..------J 74
- Panel PWB 76
- N/F PS PWB 76
- SHARP PARTS GUIDE 77
- ❑ Exteriors 78
- ~] Exteriors 79
- ICore (OP12 X 15) 79
- ,VH i TA 80
- ❑ Control PWB unit 81
- ❑ Panel PWB unit 81
- , . . -,. m. . 82
- IlnclLldeNo 101-1171 I 82
- PARTS CODE 83
- ER-OIPUKA 84
- 1997 BY SHARP CORPORATION 86
- All rights reserved 86
- SHARP CORPORATION 86
Verwandte Produkte und Handbücher für Drucken & Scannen Sharp ER-01PU
(33 Seiten)
(641 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.136 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern