Sharp ER-01PU Spezifikationen PDF herunterladen (Seite 54)

ER-OIPU

4-4. Drawer open & sense test

(1)

Operation

X Stand-alone test: SW1-40r –5+ON-LINE key ON

Note: SW1-4 = Drawer 1 or SW1-5 = Drawer 2

* Connection test:

Selection of test item+ ENTER key ON

Note: Test item =

Drawer 1 open sense test or Drawer 2

open sense test

(2) Content

The drawer is opened and the drawer open sensor state is

expressed with the print/display (connection test only).

@ Drawer open sensor test (Close test)

Result O

@ Drawer open

Visually check that the drawer is opened.

@ Drawer open sensor test (Open test)

Result 1

@ Drawer close

@ Drawer open sensor test (Close test)

Result O

(3) Check content

X Visually check that the drawer is opened.

X Check the sensor with the print/dispiay (connection test only).

@ Print(Stand-alone/Connectiontest) Drawer1

Drawer2

Testresultis 1+ O+ 1:

TESTO04:OKTESTO05:OK

Test resultis otherthan the above: TEST(I04:ERRTESTO05:ERR

@ Display (connection test only)

Example: DRAWER1 =OPEN

Item

{

State

Content

DRAWER1

OPEN/CLOSE

The state of drawer 1 open

sensor is displayed.

DRAWER2 ~ OPEN/CLOSE

The state of drawer 2 open

sensor is disDlaved.

(4) Cancel

Stand-alone test + The print is made and the testis

Connection test + Same as above.

4-5. RS232 loop test

(1)

Operation

X Stand-alone test: SW1-6 + ON-LINE key ON

(2) Content

The loop back test is performed with a service

6705RCZZ).

Control signal test

The test is made with ON/OFF of ER=DR signal.

Data transfer test

terminated.

jig (UKOG-

The loop back data transfer test of OOH- FFH (256Byte) is

performed.

Note: Test is made with the baud rate of 38,400 BPS (the

highest speed).

(3) Check content

Check the print below:

TESTO06:OK

TESTO06: EX

(4) Cancel

The above print is made and the testis terminated.

4-6. Flash ROM & CG ROM sum test

(1) Operation

X Stand-alone test: SW1-7 + ON-LINE key ON

* Connection test:

Selection of test item+ ENTER key ON

(2) Content

1) All data sum test of the flash ROM is performed.

2) Alldata sum test of the CG ROM is performed.

X Display: ROM TEST (Connection test only)

(3) Check content

Check with the following prints.

TESTO07:F-ROMOK

TESTO07:F-ROMERR

NOTE

28F40*****

28F40***** ****: ROMversion

CGROM--

GGROM---

(Normal print)

(Error print)

CGROM ---

(CG ROM not installed)

(4) Cancel

The above print is made and the test is terminated.

47. RAM test

(1) Operation

X Stand-alone test: SW1-8 + ON-LINE key ON

* Connection test: Selection of test item+ ENTER key ON

(2) Content

Tests of RAM 256Kbit x 2 PCS.are made. Memory data must not

be changed immediately before and after the test job.

@ Perform the following process for the memory byte address

(H’400000 - H’40FFFF).

PASS1: Memory save

PASS2: Data OOOOHwrite

PASS3: Data OODOHread & compile, data 5555H write

PASS4: Data 5555H read & compile, data AAAAH write

PASS5: Data AAAAH read & compile

PASS6: Memory data load

@ in case of COMPILE ERR in PASS1 -6 tests, the error print

is made. If there is no error up to the last address, the test is

terminated normally.

@ In addition, the following tests are performed. (For the

specifications of address test, refer to the flowchart on the

next page.)

TEST POINT ADDRESS= H’400000,H’400002, H’400004,

H’400008,H’40001 O,H’400020,

H’400040,H’400080, H’400100,

H’400200,H’400400, H’400800,

H’401000,H’40200(.),H’404000

X Display: RAM TEST (Connection test only)

(Normal

print)

(Error print) ‘

X= 1: ER-DR connection error

2: Not used.

3: TXD-RXD verify error

4: Time out error

10-4

1 2 ... 49 50 51 52 53 54 55 56 57 58 59 ... 85 86

Kommentare zu diesen Handbüchern

Keine Kommentare

Sharp ER-01PU Spezifikationen Seite 54

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Drucken & Scannen Sharp ER-01PU