Sharp SD-AT1000W Spezifikationen PDF herunterladen (Seite 55)

Maxiva UAX

October 17, 2013

2‐13

888‐2693‐004 WARNING:Disconnectprimarypower priortoservicing.

Figure 2-8 RF Sample Connections: Cabinet Top

2.10 InitialStart‐upProcedure

ThefollowingprocedurepresentsthestepsrequiredtoturnonsafelytheUAXtransmitterforthefirsttime.Itis

recommendedthatinstallationpersonnelfullyreadthegeneralproductdescriptioninSection1,thecontrolsand

operationmaterialinSection3,andtheseproceduresbeforestarting.

STEP 1

Openallmainscircuitprotectiondevices(breakers,fuses)asasafety

precaution.

STEP 2 Carefullyinspectthetransmitterforanyloosehardware,unconnectedwires,

missingparts,debris,orothersignsofdamagefromshipmentor

installation.

STEP 3 Verifythatthefollowingbasicrequirementshavealreadybeenmet:

• Achannel izedRFmaskfilter(ifrequiredandnotinstalledinthecabinetatthefactory)ofadequatepowerrat‐

ingisco

nnectedtothesystemRFoutput.

• Atransmittingantennaordummyloadof50ohmsisconnectedtothesystemRFoutput(usuallytothemask

filter).

• Allblowerexhaustandairinletopeningsarenotblocked,andallnecessaryductworkisinplace.

• Allrack‐mountedunitshaveacontinualACmainssafetygroundconnectionviagreen/yellowconductor(third

prong)backtothemainsafetygroundattheACserviceentrance.

• AsuitableACmainsconnectionwithsurgeprotectiondeviceshasbeenmadeperthesystemdrawings.

• Thetransmitterrackandallrack‐mountedunitshaveprotectiveRFearthgroundingasnecessary.

• TheRFmuteandsafetyinterlockshavebeensatisfied(S eeSection2.9.4onpage2‐8)

• Asuitableprograminputsignal(video,ASI,ETI,SMPTE,etc)isconnectedtotheappropriatesocketsonrear

panelofLPUorcustomerI/Opanelatthetopoftherack(whereapplicable).(See2.9.5onpa

ge2‐10)

• Ifnecessary, asuitablefrequencycontrolsignal(10MHz,GPS,1pps)isconnectedtoappropriatesocketson

rearpanelofLPUorcustomerI/Opanelatthetopoftherack(whereapplicable).(See2.9.5onpa

ge2‐10)

• ThenecessaryRFsamplestoprovidesystemoutputmeteringandRTAChavebeeninstalled.(See2.9.6on

page2‐12)

• Thepropertestequipmentisonhandtoevaluatethetransmittedsignalqualityandprovideacalibrated

meanstoverifytheoutputpowerlevel.(e.g.spectrumanalyzer,waveformmonitor/signalanalyzer,average

powermeter)

• Theoriginalfactorytestdatashippedwithtransmitterison‐handandreadyforconsultation.

STEP 4

InstalltheLPUandPABPAandPSmodules.Dependingonthetransmitter

model,thePAandPSmodulesmaybeshippedinstalledinthetransmitteror

removedandplacedinaseparateshippingcontainer.Refertothefactory

testdata.EachPAmodulehasaserialnumber.ThePAmodulewi

llworkin

anyPAslotlocationbutshouldbeinstalledinthesamepositionsinwhich

theyweretested.

1 2 ... 50 51 52 53 54 55 56 57 58 59 60 ... 291 292

Sharp SD-AT1000W Spezifikationen Seite 55

Kommentare zu diesen Handbüchern