Sharp FO-2080 Spezifikationen Seite 106
- Seite / 180
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
SW
No.
Bit
No.
ITEM Soft SW setting and function Factory Setting
8 1 Non-modulation carrier send in V.29 Non-modulation carriers are not required for V.29 Modem
transmission in ITU-TS standards. However, non-modulation
carriers can be sent in advance to image signals.
This function is effective to avoid communication troubles
due to echoes in oversea communication.
0
2 CED tone signal interval Used to set the time interval between the CED signal and
the NSF signal.
This function is effective to avoid communication troubles
due to echoes in oversea communication.
0
3 Communication error process
when receiving RTN
Used to set the communication error process for received
RTN when there is an error in transmitted image data and
RTN is returned.
1
4 NSF receive acknowledge Used to select between DIS signal recognition at 2-time
reception of DIS signal and DIS signal recognition at DIS
signal reception after NSF signal.
This function is effective to avoid communication troubles
due to echoes in oversea communication.
0
5 EOL detection timer Used to set the EOL (End of Life) detection time to 25sec
or 13sec. This function is effective to avoid a
communication error due to long EOL of certain models.
0
6 Reserved 0
7 Reserved 0
8 ECM Used to set ON/OFF of ECM. 1
91
2
Interval between OFF-HOOK and
dial send
Used to set the delay from OFF-HOOK when starting
dialing to actual send start of the dial signal.
If the dial tone detection function is enabled, this setup is
ignored.
1
1
3 Reserved 0
4 Reserved 0
5
6
Reserved 0
1
7
8
Reserved 0
1
10 1 Reserved 0
2 FAST Used to set Enable/Disable of RMS (FAST) function. 0
3 Reserved 1
4 Basic resolution Used to select the basic resolution for scanning and printing. 0
5 Reserved 0
6
7
8
Reserved 0
0
0
1 : ON 0 : OFF
1 : 500 msec 0 : 75 msec
1 : Not transmission error 0 : Transmission error
1 : Twice
0 : Once for NSF reception,
Twice for DIS reception
1 : 25 sec 0 : 5 sec
1 : ON 0 : OFF
Bit No. 0.5sec 1sec 2sec 3sec
10011
20101
1 : Enable 0 : Disable
1 : Inch series 0 : Metric series
FO-3800M
8 – 24
- FO-3800M 1
- LASER PRODUCT 2
- LASER KLASSE 1 2
- Contents 3
- [1] SYSTEM CONFIGURATION 4
- A. Main Unit 4
- B. Supplies 4
- C. Accessories 4
- 2. STRUCTURE 5
- 3. SOFTWARE 5
- 4. OPERATING ENVIRONMENT 5
- [2] SPECIFICATIONS 6
- C. Printer mode 7
- (2) Job speed 8
- (3) Image quality 8
- D. Scanner mode 10
- 4. ENGINE SPECIFICATION 18
- O. Ambient conditions 20
- [3] CONSUMABLE PARTS 21
- (1) Photoconductor drum 21
- (2) Developer cartridge 22
- 4. Paper specifications 23
- 5. Standard density sample 24
- 6. Environmental conditions 25
- [4] SET UP 26
- B. Releasing lock 27
- (1) Developer cartridge 27
- Paper tray 28
- Paper release lever 28
- View from the 28
- 4. Cable connection 29
- (Scanner) driver software 29
- 6. Setup FAX section 31
- 7. Note for transport 32
- A. External, operation parts 33
- (2) Internal operation parts 34
- 12) 13) 14) 15) 35
- B. Internal parts 37
- C. Functional parts 50
- 2) POWER SW 51
- 3) IMGSM 52
- (6) Fuse, thermostat 53
- (7) Lamp 54
- (8) Interface (connector) 54
- (9) Belt, wire 55
- (10) Power 55
- D. Lock position 56
- [6] MACHINE OPERATION 57
- (14) Others 62
- [7] ADJUSTMENTS, SETTING 63
- 64
- Not copied 65
- Work content 67
- Necessary condition 67
- D 1.0mm 68
- Copy A Copy B 70
- L=10.5+CCD No(OID) 71
- HARDDENCD 72
- STAINLESS 72
- Original Copy 73
- Allow a clearance 75
- White paper 75
- (A4, 11" x 8.5") 75
- Necessary tools 76
- Draw a line 77
- A4 (11" x 8.5") 77
- Fusing temperature adjustment 80
- Power voltage adjustment 81
- JP2 (VIN) JP3 (SH) 82
- JP1 (GND) 82
- USER PROGRAM 83
- A. Outline and purpose 83
- B. Code system simulation 83
- (2) Simulation list 85
- (3) Details of simulations 87
- ∗ Main charger voltage 90
- ∗ Transfer charger voltage 90
- ∗ Developer bias voltage 90
- B. Operating procedure 96
- C. Content 96
- 3. Printing Out Reports 97
- B. List of functions 98
- (1) Soft SW change method 99
- (2) Soft switch clear mode 99
- (3) ROM & RAM check mode 100
- (4) Signal send mode 100
- (5) Image memory clear mode 101
- (7) Dial test mode (Tone) 102
- (9) Panel check mode 102
- (10) Signal detect mode 102
- A. Software Switch List 103
- FO-3800M 112
- S001 External view section 114
- S001/P001 Rear cabinet 116
- S001/P003 Right cabinet 117
- S001/P004 Left cabinet 117
- S001/P008 Bottom base plate 118
- S002 Operation section 119
- ∗ Note for assembly 120
- S003/P001 122
- S003/P003 122
- S003/P002 122
- ∗ Cleaning 123
- ∗ Grease 123
- Scanner (Reading) section 124
- S004/Ua001 Scanner unit 126
- S004/Ub001/P001/CLN 128
- Scanner (writing) section 131
- S006 Image process section 133
- S006/P006/CLN 135
- S006/P007/CLN 135
- S006/P008/CLN 135
- S007 Fusing, paper exit 136
- S007/Ua001 Fusing unit 137
- S007/Ua001/P001/CLN 138
- S007/Ua001/P003/CLN 138
- S007/Ua001/P004/CLN 138
- S007/Ua001/P005 139
- Drive section 140
- S009 Electrical section 141
- S008/P001/GRE 141
- S008/P001/ 141
- ∗ After-work 143
- S009/Ua006 LIU PWB unit 144
- ∗ Greasing 147
- S011 Other section 149
- [10] TROUBLESHOOTING 150
- A. Outline 150
- B. Function and propose 150
- D. Self diag operation 150
- F. Details 152
- Streaks and dots in the 178
- SHARP CORPORATION 180
Verwandte Produkte und Handbücher für Drucken & Scannen Sharp FO-2080
Drucken & Scannen Sharp ARNC5J Wartungshandbuch
(12 Seiten)
(12 Seiten)
Drucken & Scannen Sharp FO-DC550 Wartungshandbuch
(216 Seiten)
(216 Seiten)
Drucken & Scannen Sharp AR-FX5 Spezifikationen
(104 Seiten)
(104 Seiten)
Drucken & Scannen Sharp AR-NB3 Wartungshandbuch
(44 Seiten)
(44 Seiten)
Drucken & Scannen Sharp AR-M280N Spezifikationen
(32 Seiten)
(32 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.095 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern