Sharp FO-2080 Spezifikationen Seite 64
- Seite / 180
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
∗
Enforcement conditions (time)
Enforcement
time
JOB No Content
S 009/Ua 002 When replacing MCU PWB.
In case of U2 trouble
When installing
When the fluorescent lamp
flickers during operation of the
copier.
Cycle —
Condition —
∗
Job content
1) Enter the simulation 26-30 mode.
(The currently set code of the CE mark conformity operation
(protecting against flicker) is displayed.
2) Enter the desired code (value) of the CE mark conformity opera-
tion (protecting against flicker), and press the start button.
Set code
CE mark conformity operation
(Protecting against flicker)
0 YES
1NO
If the fluorescent lamp flickers when the power of the copier is
turned on, set this adjustment value to 1 to reduce or eliminate
this phenomenon.
SET M2 Counter setting
SET 1 Photoconductor counter reset
∗
Enforcement condition (time)
Enforcement
time
JOB No Content
When replacing
photoconductor cartridge
S 009/Ua 002 When replacing MCU PWB
In case of U2 trouble
Cycle 20 K
Condition —
∗
Job content
1) Turn on the power.
2) Open the operation section. (The cabinet switch is turned off.)
3) While pressing the copy mode select key (left and side) and the
clear key simultaneously, close the operation section. (The cabinet
switch is turned on.) (This state is maintained for 5 sec.)
With the above operation, the photoconductor counter is reset.
ADJ M1 Copy density adjustment
∗
Execution condition (time)
Enforcement
time
JOB No Content
S 004 When any part of the scanner
(reading) section is
disassembled, replaced, or
cleaned.
S 009/Ua 002 When replacing MCU PWB
In case of U2 trouble
S 009/Ua 004 When replacing the high
voltage power/motor drive PWB
ADJ M6 When adjusting the high
voltage power voltage
When servicing
Cycle —
Conditions Normal copy exposure is not
obtained.
∗
Necessary condition
1) The scanner (reading) section must be free from dust.
2) The image process section must be normal.
★ The high voltage power voltage must be normal.
★ The photoconductor cartridge, the developer cartridge are nor-
mal (free from dirt and damage).
★ The transfer roller must be free from dirt and damage.
3) The fusing section must be normal (free from dirt).
4) The paper transport section must be normal.
5) The scan (writing) section must be free from dirt.
∗
Adjustment value (Common to all the adjustment items)
(Test command (Set value))
Range (MIN) 0
Range (MAX) 99
Standard value 50
Default 50
ADJ 1 Auto copy mode copy density adjustment
ADJ 2 Manual copy mode copy density
adjustment
ADJ 3 Photo copy mode copy density adjustment
ADJ 4 Auto (Toner save) copy mode copy
density adjustment
ADJ 5 Manual (Toner save) copy mode copy
density adjustment
(Copy density level)
Adjustment
mode
Mode display
lamp
Density
adjustment
level
SHARP gray chart
(UKOG-0062FCZZ)
adjustment level
Auto copy
mode
Auto copy
mode lamp
"3" of the gray
scale is copied.
Test copy
mode
Text copy
mode lamp
Center (3) "3" of the gray
scale is copied.
Photo copy
mode
Photo copy
mode lamp
Center (3) "2" of the gray
scale is copied.
Auto (Toner
save) copy
mode
Auto copy
mode lamp
"3" of the gray
scale is copied.
Photo copy
mode lamp
Manual
(Toner save)
copy mode
Manual copy
mode lamp
Center (3) Gray scale "3" is
copied.
Photo copy
mode lamp
FO-3800M
7 – 2
- FO-3800M 1
- LASER PRODUCT 2
- LASER KLASSE 1 2
- Contents 3
- [1] SYSTEM CONFIGURATION 4
- A. Main Unit 4
- B. Supplies 4
- C. Accessories 4
- 2. STRUCTURE 5
- 3. SOFTWARE 5
- 4. OPERATING ENVIRONMENT 5
- [2] SPECIFICATIONS 6
- C. Printer mode 7
- (2) Job speed 8
- (3) Image quality 8
- D. Scanner mode 10
- 4. ENGINE SPECIFICATION 18
- O. Ambient conditions 20
- [3] CONSUMABLE PARTS 21
- (1) Photoconductor drum 21
- (2) Developer cartridge 22
- 4. Paper specifications 23
- 5. Standard density sample 24
- 6. Environmental conditions 25
- [4] SET UP 26
- B. Releasing lock 27
- (1) Developer cartridge 27
- Paper tray 28
- Paper release lever 28
- View from the 28
- 4. Cable connection 29
- (Scanner) driver software 29
- 6. Setup FAX section 31
- 7. Note for transport 32
- A. External, operation parts 33
- (2) Internal operation parts 34
- 12) 13) 14) 15) 35
- B. Internal parts 37
- C. Functional parts 50
- 2) POWER SW 51
- 3) IMGSM 52
- (6) Fuse, thermostat 53
- (7) Lamp 54
- (8) Interface (connector) 54
- (9) Belt, wire 55
- (10) Power 55
- D. Lock position 56
- [6] MACHINE OPERATION 57
- (14) Others 62
- [7] ADJUSTMENTS, SETTING 63
- 64
- Not copied 65
- Work content 67
- Necessary condition 67
- D 1.0mm 68
- Copy A Copy B 70
- L=10.5+CCD No(OID) 71
- HARDDENCD 72
- STAINLESS 72
- Original Copy 73
- Allow a clearance 75
- White paper 75
- (A4, 11" x 8.5") 75
- Necessary tools 76
- Draw a line 77
- A4 (11" x 8.5") 77
- Fusing temperature adjustment 80
- Power voltage adjustment 81
- JP2 (VIN) JP3 (SH) 82
- JP1 (GND) 82
- USER PROGRAM 83
- A. Outline and purpose 83
- B. Code system simulation 83
- (2) Simulation list 85
- (3) Details of simulations 87
- ∗ Main charger voltage 90
- ∗ Transfer charger voltage 90
- ∗ Developer bias voltage 90
- B. Operating procedure 96
- C. Content 96
- 3. Printing Out Reports 97
- B. List of functions 98
- (1) Soft SW change method 99
- (2) Soft switch clear mode 99
- (3) ROM & RAM check mode 100
- (4) Signal send mode 100
- (5) Image memory clear mode 101
- (7) Dial test mode (Tone) 102
- (9) Panel check mode 102
- (10) Signal detect mode 102
- A. Software Switch List 103
- FO-3800M 112
- S001 External view section 114
- S001/P001 Rear cabinet 116
- S001/P003 Right cabinet 117
- S001/P004 Left cabinet 117
- S001/P008 Bottom base plate 118
- S002 Operation section 119
- ∗ Note for assembly 120
- S003/P001 122
- S003/P003 122
- S003/P002 122
- ∗ Cleaning 123
- ∗ Grease 123
- Scanner (Reading) section 124
- S004/Ua001 Scanner unit 126
- S004/Ub001/P001/CLN 128
- Scanner (writing) section 131
- S006 Image process section 133
- S006/P006/CLN 135
- S006/P007/CLN 135
- S006/P008/CLN 135
- S007 Fusing, paper exit 136
- S007/Ua001 Fusing unit 137
- S007/Ua001/P001/CLN 138
- S007/Ua001/P003/CLN 138
- S007/Ua001/P004/CLN 138
- S007/Ua001/P005 139
- Drive section 140
- S009 Electrical section 141
- S008/P001/GRE 141
- S008/P001/ 141
- ∗ After-work 143
- S009/Ua006 LIU PWB unit 144
- ∗ Greasing 147
- S011 Other section 149
- [10] TROUBLESHOOTING 150
- A. Outline 150
- B. Function and propose 150
- D. Self diag operation 150
- F. Details 152
- Streaks and dots in the 178
- SHARP CORPORATION 180
Verwandte Produkte und Handbücher für Drucken & Scannen Sharp FO-2080
Drucken & Scannen Sharp ARNC5J Wartungshandbuch
(12 Seiten)
(12 Seiten)
Drucken & Scannen Sharp FO-DC550 Wartungshandbuch
(216 Seiten)
(216 Seiten)
Drucken & Scannen Sharp AR-FX5 Spezifikationen
(104 Seiten)
(104 Seiten)
Drucken & Scannen Sharp AR-NB3 Wartungshandbuch
(44 Seiten)
(44 Seiten)
Drucken & Scannen Sharp AR-M280N Spezifikationen
(32 Seiten)
(32 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern