Sharp JX-9400 Technical Information Seite 118
- Seite / 211
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Best net ene rgy savings in large units (7 and 8 in Table 5.2) are 80,000–
90,000 kWh per winter season, but unit 10 actually wastes as much energy.
Small units (a, b and c) save between 80 kWh and 350 kWh during an entire
season. From an energy and economic lifetime analysis perspective, such
units are disadvantageous.
Note that these results are obtained when the heat recovery is functioning.
Annual average efficiency may even be less due to reduced operation time
(Drost, 1993).
Energy for ventilation
The energy to move the air is the produ ct of a force by a displacement. The
force is the pressure, p, exerted on the section area, A, of the duct, and the
displacement is the path, l, of the air during a time interval, t. But A l is
the volume of air displaced during this time interval. The energy to move a
volume V of air is hence:
E
m
¼ pA l ¼ pV ð5:44Þ
Taking a time derivative of the above equation provides the mechanical power ,
m
, needed to get an airflow ra te, q:
m
¼
dE
m
dt
¼ p
dV
dt
¼ pq ð5:45Þ
The mechanical power delivered by a fan is the product of the volume airflow
rate, Q, delivered by the fan, and the pressure differential, p, across the fan.
The mechanical power required to move the air through a ductwork is also the
product of the volume airflow rate through the ductwork, and the pressure
difference between the main supply and main exhaust ducts. Since the pressure
difference is proportional to the square of the airflow rate, the mechanical
power for ensuring a given airflow rate into a ductwork is proportional to the
cube of the airflow rate! Increasing the airflow rate in a room by 10 per cent
requires 33 per cent more fan power and doubling the airflow rate requires a
power eight times larger if the ductwork is not adapted to this new airflow rate.
Why check fan power and related quantities?
The electrical energy needed to move the air depends on the properties of the
air distribution system and of the fan. For a given nominal power, efficiencies
varying by a factor two or more were measured (see ‘Examples of application’,
below). Assessing the fan efficiency and the specific power (in Joules or
Watt-hours per cubic metre of transported air) is part of a comprehensive
energy diagnosis of a mechanical ventilation sy stem.
Poor fan efficiency not only wastes expensive electric energy, but also
hinders efficient cooling. The cooling power of the air blown by the fan is:
cool
¼ cQ ¼ cq ð5:46Þ
Measurements and Measures Related to Energy Efficiency in Ventilation 97
- Claude-Alain Roulet 4
- Contents 6
- List of Figures and Tables 8
- List of Figures and Tables ix 10
- List of Figures and Tables xi 12
- Preamble 13
- Introduction 14
- Outdoor airflow rate 15
- Recirculation rates 16
- Exfiltration 17
- Ventilation efficiency 18
- Airtightness 20
- Energy efficiency 20
- Common techniques 21
- Airflow Rates in Buildings 22
- Tracer decay, no injection 24
- Constant injection rate 24
- Constant concentration 25
- Pulse injection 25
- Airflow Rates in Buildings 5 26
- Airflow Rates in Buildings 7 28
- Global system of equations 29
- Airflow Rates in Buildings 9 30
- Properties of the flow matrix 31
- Airflow Rates in Buildings 11 32
- Note: y Under condition 34
- Source: Sherman, 1990 34
- Airflow Rates in Buildings 13 34
- Airflow Rates 36
- Source: Roulet et al., 2000a 37
- Velocity traverse 38
- Test procedure 39
- Tracer gas dilution 39
- Source: Awbi, 2007 40
- Inflatable bag 41
- Flowmeter 41
- Compensated flowmeter 41
- Tracer gas injection ports 41
- Source: Roulet et al., 1999 42
- Node by node method 44
- Least square solution 48
- Eliminating some equations 48
- Simplest way 49
- Less than four tracer gases 53
- Planning tool 54
- Simple measurement using CO 55
- Age of Air and 60
- Ventilation Efficiency 60
- Nominal time constant 61
- Air exchange efficiency 61
- Source: Roulet, 2004 62
- Measurement method 63
- Concentration [ppm] 65
- Source: Roulet et al., 1998 69
- The model matrix M 73
- Condition of the model matrix 74
- Factorial designs 75
- 3-D designs 76
- Measurement methods 80
- Reductive sealing 82
- Density corrections 84
- Two measurement points 85
- Airtightness 65 86
- Airtightness of buildings 88
- External fan 89
- Internal fan 90
- Leakage visualization 90
- The stack effect method 91
- Airtightness 71 92
- Neutral height method 93
- Airtightness 73 94
- Pressurization method 95
- Flow rate difference method 96
- Conditioned space 97
- SealSeal 97
- Measurements and Measures 98
- Related to Energy Efficiency 98
- Energy in air handling units 100
- Heat exchangers 104
- Types of heat exchangers 105
- Rotating heat exchangers 106
- Glycol heat exchanger 107
- Heat pump 107
- Heat exchange efficiency 107
- Ventilated 110
- Global heat recovery efficiency 111
- Source: Roulet et al., 2001 114
- Examples of application 115
- Energy for ventilation 118
- Measurement of airflow rate 120
- Measurement of electric power 121
- Simulation results 126
- Recirculation 126
- Humidification 127
- Heat recovery 127
- Ductwork 128
- Contaminants in 129
- Air Handling Units 129
- Source: Bjo 130
- Humidifiers 131
- Source: Roulet et al., 2000 133
- Measurement protocols 134
- Selecting the panel 135
- Source: Bluyssen, 1990 136
- Training procedure 137
- Experimental day 138
- Principle of the method 138
- Injection technique 139
- Hot air blower (200 °C) 140
- Stainless steel 140
- Ø 6 mm copper tube 140
- Example of application 141
- Evidence for adsorption 144
- HVAC systems 146
- Common Methods 153
- Properties of tracer gases 155
- Source: Dietz et al., 1983 157
- Mixing tracer gases 158
- Tracer density problem 159
- Sampling methods 160
- Grab sampling 160
- Passive sampling 160
- Networks, pumps and pipes 161
- Tracer gas analysers 163
- Objective of the analysis 163
- Photo-acoustic detector 165
- Mass spectrometry 165
- Gas chromatography 167
- Chemical indicator tubes 167
- Identification methods 168
- Confidence in the coefficients 170
- Regression of the second kind 171
- Orthogonal regression 171
- Bayesian identification 172
- Error analysis 174
- Definitions 175
- A few statistics 175
- Covariance 177
- Statistical distributions 177
- What is the problem? 180
- Most simple error analysis 180
- Estimate of the variance 181
- Linear equations systems 181
- Upper bound of the errors 183
- References 187
- Unit Conversion Tables 192
- Pressure 194
- Volume flow rate 194
- Mass flow rate 194
- Glossary 195
- Glossary 175 196
- Glossary 177 198
- Glossary 179 200
- Glossary 181 202
- Glossary 183 204
- Glossary 185 206
Verwandte Produkte und Handbücher für Drucken & Scannen Sharp JX-9400
Drucken & Scannen Sharp SF-1020 Wartungshandbuch
(140 Seiten)
(140 Seiten)
Drucken & Scannen Sharp ER-01PU Spezifikationen
(86 Seiten)
(86 Seiten)
(641 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.019 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern